3625 BROADWAY SONIS KITCHEN 2025-01-03

SECTION 3-SYSTEM COMPONENTS R-102 Restaurant Fire Suppression Manual R-102 Restauranf Fire Suppression Manual SECTION 3-SYSTEM CDMPONENTS UL EX3470 ULC EX3470 UL EX3470 ULC EX3470 PAGE 3-6 REV.11 2014-SEP-01 2014-SEP-01 REV,11 PAGE 3.7 SWIVEL ADAPTOR CONDUIT OFFSET ASSEMBLY "COMPRESSION-SEAL"ADAPTOR *COCKING LEVERILOCK PIN The Swivel Adaptor Assembly consists of a swivel nut,swivel The conduit offset assembly (Part No. 435961)Is used to This adaptor is a mechanical bulkhead tilting that produces a The cocking lever is a component required to cock(arm)both body and swivel ball.All are chrome-plated.The Swivel adaptor change direction of the wire rope on detection,mechanical gas liquid-fight seal around pipe and conduit when Installing distribu- the mechanicallelectrical AUTOMAN release and the moch- allows any nozzle to be rotated approximately 30"in all direc- valve,and remote Pull station fines.The conduit offset assem- tion piping and detection conduit through restaurant hoods and f anical gas valve.After the AUTOMAN is cocked(armed),the tons.Swivel Adaptors must be ordered as a Swivel Adaptor illy can only be used in the area where the conduit attaches to ducts.The"Compression-Seal"adaptor is a straight-through .lock pin must be Inserted to eliminate the accidental tiring of j Shipping Assembly(Part No.423572)which contains 25 Swivel the regulated release assembly.When using the conduit offset design requiring no cutting or threading of conduit or pipe.The the release mechanism.These components are available as Adaptors or Part No.419385.which contains 9 Swivel Adaptors. assembly,the maximum number of pulley elbows allowed Is adaptor is available for pipe sizes of 114 In.(Part No.79149), either an individual shipping assembly or a shipping assembly •16•The Conduit Offset Shipping Assembly(Purl No.436063) 318 in.(Part No.79161),1121n.(Pan No.79147),and EMT con- containing both.Listed below are the various shipping assam- Lr�FFMALE T THREAT) consists of 6 conduit offsets. duit Size of 112 in.(Part No.79153).Each"Compression-Seal" biy part numbers. CON oixr Adaptor Shipping Asset"must he ordered as slated below: Part No. Description COUPLING Shipping .441042 Short Handle Cocking Lever with Lock Pin Assembly Hole Sire Size Part No. Required (MechanicaUElectdca!AUTOMAN) { are-ire NPT CONDUIT TA In.Pipe 1112 in.lobe 79149 24 314 il. •441041 Long Handle Cocking Lever with Lock Pin 5 3D DEGREE�� MALE THREAD OFFSET 3/81n Pipe 1 6!8 in.tube 79161 24 1 118 in. (MechatticallEler-[rice!AUTOMAN) s ROTAnONN 112 in.Pipe 79147 24 1 110 in. .26310 Cocking Lever only(AUTOMAN P-C) FIGURE 3-15 112 in.EMT Conduit 79153 24 1 118 In. � 416018 Cocking Lever only(Mechanics!Gas Valve) CONDUIT COMPRESSION NUT F 438031 Lock Pin •METAL BLOW-OFF CAP CONNECTOR The Metal Blow-Off Cap helps keep the orifice of the nozzle free ADAPTOR BODY9e Short Handle Cocking Lever of grease or other substances that could Interfere with agent GASRLI—. LOCNWASHER distribution. FIGURE 3-18 a �� •The Metal Blow-Off Cap Package(Part No.439861)contains 00n11 FIGURE3-20 aem,ue:eoeaeN wreMn« 10 blow-off caps. ooDlss aRaa crmmax wrench • ' Also available Is a 10 pack of Stainless Steel Blow-Off Caps 1'hehe""SEAL"ADAPTOR - (Part No.439866). "QIrIk-Seal-adaptor is a listed mechanical bulkhead filling "HOOD SEAL"ADAPTOR ASSEMBLY that produces a liquid-tight Seal around both distribution piping This adaptor Is a mechanical bulkhead filling that produces a and detection conduit which runs through restaurant hoods and liquid-tight seal around 112 in.EMT conduit when installing the ducts.The"Quirk-Seal"adaptor accepts threaded pipe or con- detection flne through restaurant hoods and duct.The adap- Long Handle Cocking Lever , duil.The adaptor is available for 1(4 in.(Part No.18196),318 in. lilt accepts a high temperature pulley elbow and,when used, (Part No.77285),112 in,(Pan No.77287),or 314 in.(Part No. correctly positions the elbow or conduit In line with the conduit p CAP 77289)pipe or conduit sizes.When using with EMT conduit,a adaptor hole in the detector bracket.The"Hood Seal"efimi- sri iE wn conduit connector must be installed In each end of the adaptor. nates the need for multiple elbows when penetrating the top of The"Quirk-Sear"Adaptor Shipping Assembly must be ordered a hood when installing the detection line."Hood Seal"Adaptors FIGURE 3-16 as staled below: are available In quantities of six as Shipping Assembly Part No. 00a4R Shipping 423253. REDUCING COUPLING - Assembly Hole Size Size Part No. � Required jj.AsKET nT .Lock Pin The reducing Coupfmg(Part No.436228)Is made of Stainless steel material with 318 in.x 11Z in.NPT inlet threads.If-neces- 1f4 tm 78198 24 314 In. SEALwasrrca sary,the reducing coupling can be utilized when installing the 3181n. 77285 24 1 118In. BODADAProR Agent Distribution Hose Line Kit(Part No.435982).Two cou- 712 in, 77M 24 1 T18 in. BOUY plings are required per Agent Distribution Hose. 314 il. 77289 24 1 3/8 m PULLEYAPTOR BODY ELBOW(NOT PA i 1N iN. GASKET OF rt5@A-SBLY) 16 ram)-a LOCRW PI LEY ASHER USE ONLY PLEY MOW,PART NO.42325Q FIGURE 3321 FIGURE 3---22 "I NUT 1 3F1a W. PDmM FIGURE 3D-D19 FIGURE 3-17 i i