1321 COLBY AVE 8TH FLOOR 2024-12-31

0,,Simp1Ex TrueAlarm Analog Sensing UL, ULC, CSFM Listed; FM Approved, TrueAlarm Analog Sensors — Photoelectric MEA (NYC) Acceptance* and Heat; Standard Bases and Accessories TrueAlarm analog sensing provides: • Digital transmission of analog sensor values via IDNet or MAPNET II two-wire communications For use with the following Simplex®products: • 4007ES,4010,4010ES,4100ES,and 4100U Series control panels;and 4008 Series control panels with reduced feature set(refer to data sheet S4008-0001 for details) • 4020,4100,and 4120 Series control panels,Universal Transponders,and 2120 TrueAlarm CDTs equipped for 4098-9714 TrueAlarm Photoelectric MAPNET II operation Sensor Mounted in Base Fire alarm control panel provides: • Peak value logging allowing accurate analysis of each - • • sensor for individual sensitivity selection • Sensitivity monitoring satisfying NFPA 72 sensitivity Digital Communication of Analog Sensing.TrueAlarm testing requirements;automatic individual sensor calibration analog sensors provide an analog measurement digitally check verifies sensor integrity communicated to the host control panel using Simplex addressable communications.At the control panel,the data is • Automatic environmental compensation,multi-stage alarm analyzed and an average value is determined and stored.An operation,and display of sensitivity directly in percent per alarm or other abnormal condition is determined by comparing foot the sensor's present value against its average value and time. • Ability to display and print detailed sensor information in plain English language Intelligent Data Evaluation.Monitoring each sensor's average value provides a continuously shifting reference point. Photoelectric smoke sensors provide: This software filtering process compensates for environmental • Seven levels of sensitivity from 0.2%to 3.7% factors(dust,dirt,etc.)and component aging,providing an (refer to additional information on page 3) accurate reference for evaluating new activity.With this Heat sensors provide: filtering,there is a significant reduction in the probability of • Three fixed temperature sensing thresholds: 135'F, 155'F false or nuisance alarms caused by shifts in sensitivity,either up and 190'F or down. • Rate-of-rise temperature sensing Control Panel Selection.Peak activity per sensor is stored to • Utility temperature sensing assist in evaluating specific locations.The alarm set point for each TrueAlarm sensor is determined at the host control panel, • Listed to UL 521 and ULC-5530 selectable as more or less sensitive as the individual application General features: requires. • Operation is for ceiling or wall mounting Timed/Multi-Stage Selection.Sensor alarm set points can be • Listed to UL 268 and ULC-S529 programmed for timed automatic sensitivity selection(such as • Louvered smoke sensor design enhances smoke capture by more sensitive at night,less sensitive during day).Control panel directing flow to chamber;entrance areas are minimally programming can also provide multi-stage operation per sensor. visible when ceiling mounted For example,a 0.2%level may cause a warning to prompt • Designed for EMI compatibility investigation while a 2.5%level may initiate an alarm. • Magnetic test feature is provided Sensor Alarm and Trouble LED Indication.Each sensor • Different bases are available to support a supervised or base's LED pulses to indicate communications with the panel.If unsupervised output relay,and/or a remote LED alarm the control panel determines a sensor is in alarm,or is dirty or has some other type of trouble,the details are annunciated at the indicator control panel and that sensor base's LED will be turned on Additional base reference: steadily.During a system alarm,the control panel will control • For isolator bases,refer to data sheet 54098-0025 the LEDs such that an LED indicating a trouble will return to • For sounder bases,refer to data sheet S4098-0028 pulsing to help identify the alarmed sensors. • For photo/heat sensors,refer to data sheet S4098-0024 (single address)and S4098-0033(dual address) These products have been approved by the California State Fire Marshal(CSFM)pursuant to Section 13144.1 of the California Health and Safety Code.See CSFM Listings 7272-0026:218,7271-0026:231,7270-0026:216,and 7300-0026:217 for allowable values and/or conditions conceming material presented in this document.Accepted for use—City of New York Department of Buildings—MEA35-93E.Additional listings may be applicable, contact your local Simplex product supplier for the latest status.Listings and approvals under Simplex Time Recorder Co.are the property of Tyco Fire Protection Products. S4098-0019-23 8/2017