5900 36TH AVE W 2025-01-06 - Laserfiche WebLink

McGraw-Edison GalleonGALN Control Options 0-10V(DIM) This fixture is offered standard with 0-10V dimming driver(s).The DIM option provides 0-10V dimming wire leads for use with a lighting control panel or other control method. Photocontrol(BPC,PR and PR7) Optional button-type photocontrol(BPC)and photocontrol receptacles(PR and PR7)provide a flexible solution to enable"dusk-to-dawn"lighting by sensing light levels.Advanced control systems compatible with NEMA 7-pin standards can be utilized with the PR7 receptacle. After Hours Dim(AHD) This feature allows photocontrol-enabled luminaires to achieve additional energy savings by dimming during scheduled portions of the night.The dimming profile will automatically take effect after a"dusk-to-dawn"period has been calculated from the photocontrol input.Specify the desired dimming profile for a simple,factory-shipped dimming solution requiring no external control wiring.Reference the After Hours Dim supplemental guide for additional information. Dimming Occupancy Sensor (SPB) These passive infrared(PIR)sensors are factory installed in the luminaire housing.When the SPB sensor option is selected,the occupancy sensor is connected to a dimming driver and the entire luminaire dims when no motion is detected.After a period of time,the luminaire turns off,and when motion is detected,the luminaire returns to full light output.The SPB sensor default parameters are listed in the table below,and can be configured utilizing the Sensor Configuration mobile application for iOS and Android devices.The SPB/X is configured to control only the specified number of light squares.An integral photocontrol can be activated with the app for"dusk-to-dawn"control or daylight harvesting-the factory default is off.Three sensor lenses are available to optimize the coverage pattern for mounting heights from 8'-40'.Four sensor colors are available;Bronze,Black,Gray and White,and are automatically selected based on the luminaire finish as indicated by the table below. SPB sensor finish matched to luminalre finish SPB/X Availability Table Luminaire Finish SPB Sensor Finish Fixture Square Count Available SPB/X Square Count WH White White 1 Not Available BK Black Black 2 Not Available GM Graphite Metallic Black 3 Not Available BZ Bronze Bronze 4 2 AP Gray Gray 5 2 or 3 DP Dark Platinum Gray 6 3 7 2,3,4or5 8 2,3,5or6 9 3or6 WaveLinx Wireless Control and Monitoring System Operates on a wireless mesh network based on IEEE 802.15.4 standards enabling wireless control of outdoor lighting.WaveLinx and WaveLinx Lite sensors utilize the Zhaga Book 18 compliant 4-PIN receptacle(ZD or ZW),while the WOLC control module utilizes a 7-PIN receptacle.ZW option provides 4-PIN receptacle and control module to enable future installation of WaveLinx sensors. ZD option provides 4-PIN receptacle and sensor-ready(SR)driver to enable future installation of WaveLinx sensors,power monitoring,and advanced functionality.WaveLinx(SWPD4 to SWPD5) outdoor wireless sensors offer passive infrared(PIR)occupancy and photocell for closed loop daylight harvesting,and can be factory or field-installed.Sensors are factory preset to dim down to 50%after 15 minutes of no motion detected.Two lens options are available for mounting heights of 7'to 40'.Use the WaveLinx mobile application for set-up and configuration.At least one Wireless Area Controller(WAC)is required for full functionality and remote communication(including adjustment of any factory pre-sets).WaveLinx Lite(WOF and WOB)outdoor wireless sensors provide PIR occupancy and photocell for closed loop daylight harvesting,and can be factory or field-installed.Sensors are factory preset to dim down to 50%after 15 minutes of no motion detect- ed.Two lens options are available for mounting heights of 7'to 40'.Use the WaveLinx Lite mobile application for set-up and configuration.WAC not required.WaveLinx Outdoor Control Module (WOLC-7P-10A)accessory provides a photocontrol enabling astronomic or time-based schedules to provide ON,OFF and dimming control of fixtures utilizing a 7-PIN receptacle.The out-of-box functionality is ON at dusk and OFF at dawn. For mounting heights up to 15'(SWPD4 and WOB) For mounting heights up to 40'(SWPD5 and WOF) 11 0' r111 201 1f-s I 0� ------ ----------- 50 •^alit a i��I-7I �,`�ln, I 5' 10, T / s 0, 25' 40 ft 10' 0-1 �'1``� 15' � 0' 100' 15' 10 - � 27' ---- --- - - - - — ------ 25 �"JV 20' 20'- 1/ 40' 50' 20'18'15'12'9' 6' 3' 0'3' 6' 9' 12'15'18'20' 20' 10' 0' 10' 20' 20' 40' 30' 20' 10' 0' 10' 20' 30' 40' 50' 50' 25' 0' 25' 50' LumenSafe Integrated Network Security Camera(LD) Cooper Lighting Solutions brings ease of camera deployment to a whole new level.No additional wiring is needed beyond providing line power to the luminaire.A variety of networking options allows security integrators to design the optimal solution for active surveillance.As the ideal solution to meet the needs for active surveillance,the LumenSafe integrated network camera is a streamlined,outdoor-ready fixed dome that provides HDTV 1080p video.This IP camera is optimally designed for deployment in the video management system or security software platform of choice. Synapse(DIM10) SimplySNAP integrated wireless controls system by Synapse.Includes factory installed DIM10 Synapse control module and MS/DC motion sensor;requires additional Synapse system components for operation.Contact Synapse at www.synapsewireless.com for product support,warranty and terms and conditions. Cooper Lighting Solutions ©2022 Cooper Lighting Solutions 00) COOPER 1121 HighwaySouth All Rights Reserved. Peachtree City,ity,GAGA 30269 PS500052EN page 11 P:770-486-4800 Specifications and dimensions P 9 Lighting Solutions www.cooperlighting.com subject to change without notice. July 15,2022 4:49 PM