Laserfiche WebLink
2018 IBC/NDS 2015 - Shear Wall Framing Clips <br /> 01/SP Allowable Lt3ade SPF/HF Allowable Loads <br /> Model Type bf Fasteners Direction _�.._ <br /> No: connection. in. of Load Floor Roof Floor hoof <br /> {12� (160}: tiDD} (125) (160) . <br /> F1 395 465 4E 340 ! 400 400 <br /> DO (8)0.131 x 1'/� — � <br /> Fe 395 430 430 � 340 370 370 <br /> A34 Fj 640 640 640 550 560 550 <br /> (8)#9 x 11/2 SD F2 495 495 4c 425 425 425 <br /> Uplift 240 240 240 170 170 170 <br /> : ... Al3Q0 300 <br /> .... .. . <br /> { 0131 x 1'/� E 295 ` 36fl 385' P55 310 <br /> A2 295 325 3 8 i:.`:.. 255.: : 280' 280 <br /> 330 330 255 285 285 <br /> 225. 225 225' 195 195 195 <br /> (12) ,131 x 11/2 <br /> 590i50 G50 510 56?} don <br /> s <br /> 590 ` 670- - 670.`...,, .. 510 576 575 <br /> 420 420 420 360 360 360 <br /> G 580 625 625 500 l 540 <br /> p : (12)0.131 x 11/2 <br /> H 580 525 525 500 450 450 <br /> :. <br /> 580 i65 56f 500 �65'.. 485 <br /> . .(12).04 1 x1'/z <br /> :. .. . ::.: H 545 490 49C1 470 4J 420 <br /> 1. Allowable loads are for one angle.When angles are installed on each side of the joist,the minimum joist thickness is 3". <br /> 2. Some illustrations show connections that could cause cross-grain tension or bending of the wood during loading if not <br /> reinforced sufficiently. In this case,mechanical reinforcement should be considered. <br /> 3. LTP4 can be installed over 3/8"wood structural panel sheathing with 0,131"x 1 1/2"nails and achieve 0.72 of the listed load, <br /> or over 1/2"sheathing and achieve 0.64 of the listed load.0.131"x 2 1/2"nails will achieve 100%load. <br /> 4. LTP4 satisfies the IRC continuously sheathed portal frame(CS-PF)framing anchor requirements when installed over raised <br /> wood floor framing per Figure R602.10.6.4, <br /> 5. The LTP5 may be installed over wood structural panel sheathing up to 1/2"thick using 0.131"x 1 1/2"nails with no reduction <br /> in load. <br /> 6. Connectors are required on both sides to achieve F2 loads in both directions. <br /> 7. Fasteners: Nail dimensions in the table are diameter by length. SD screws are Simpson Strong-TieO Strong-Drive®screws. <br /> PH6121 is a pan-head#6 x 1/2"screw available from Simpson Strong-Tie. For additional information, see Fastener Types and <br /> Sizes Specified for Simpson Strong-Tie Connectors. <br /> rP <br /> -6U 144-plf E 560# 7-c- <br /> 540# 44"oc <br /> -6 240- If E 560# 540# 27"oc <br /> -4 350- If E 560# 540# 18"oc <br /> P1-3 450-plf(E 560# 14 540# 14"oc <br /> P1-2 820- If W 560# 7'/z"oc 540# 7'/z"oc <br /> LTP5 18"oc+ r <br /> P2-4 700-pif(E) 560# 9"oc 540# A35 18"oc <br /> LTP5 14"oc+ <br /> P2 3 900 p1f(E( 560# 7"oc 540# A35 14"oc <br /> 8"oc+ <br /> P2 2 1640-p1f(W( 560# 2 rows 8"oc 540# A LTP5 35 8"oc <br /> L3.3 <br />