1825 BROADWAY 2025-05-02 - Laserfiche WebLink

DF-60241:E•B-105 ANN-LED LED Annunciator Module FirelffeALarms by Honeywell Annunciators General The ANN-LED annunciator module provides LED annunciation of general system faults and input zones/points when used with a com- INS FaWt FaW as Fa°" patible Fire Alarm Control Panel(FACP).The ANN-LED module pro- videsEarth BFauA �Fa n` o:aoiee Maa•aa�a alarm (red), trouble (yellow) and supervisory (yellow) Fa° wNEz wNEa ®wNEa ©woes ( ) (Y ) p Y (Y ) indication for up to ten input zones or addressable points. ANN- o RLED has red LEDs only for alarm communication of up to 30 addressable points. The ANN-LED is supplied standard with certain Canadian FACPs as wNE b p 7pVE 7 p wNE 8 required by ULC. The ANN-LED and the FACP communicate over a two-wire serial interface employing the ANN-Bus communication format. An addi FIR ALARM ANNUNCIATOR - tional two wires are used for 24-volt DC power. A single four-con- ductor unshielded cable may be used for both power and data communications. Up to eight ANN-Bus devices may be connected to the ANN-Bus of Ordering Information each FACP. ANN-LED: annunciator module with alarm (red), trouble (yellow) and supervisory (yellow) indication for up to ten input zones or Features addressable points, includes module mounting bracket, metal cover • ANN-LED connects to the ANN-Bus terminal on the FACP and and clear plastic screen, rubber display/label holder, screws for requires minimal programming securing the metal cover and the backbox, red enclosure • Includes three LEDs for each zone:Alarm, Trouble and Supervi- ANN-LED-W: same as above, with gray enclosure and white key- sory. pad • Compatible with the ES-200X, ES-50X, MS-9600(UD)LS, MS- ANN-RLED: annunciator module with alarm (red) indicators for up 92000DLS, MS-9050UD, MS-5UD, MS-10UD, MRP-2001, and to 30 input zones or addressable points, includes red enclosure MRP-2002, ANN-RLED-W: same as above, with gray enclosure and white key- Can be remotely located up to 6,000 feet (1,829 m) from the pad panel • May be powered by 24 VDC from the host FACP or by remote Agency Listings and Approvals power supply(requires 24 VDC) The listings and approvals below apply to the ANN-LED. In some Specifications cases, certain modules may not be listed by certain approval agen- cies, or listing may be in process. Consult factory for latest listing • Maximum ANN-BUS Voltage:24 VDC status. • Maximum Current:Alarm: 68 mAStandby:28 mA UL: S2424 • Maximum wiring distance from FACP:6,000 ft. (1,829 m.) ULC: S2424(ANN-LED only) • Ambient Temperature: 32°F to 120°F(0°C to 49°C) FM approved • Relative Humidity:93%±2%RH (non-condensing)at 32°C±20C CSFM: 7120-0075:0222 (90OF±30F) MEA: 333-07-E • For use indoors in a dry location Fire Dept of NY: COA#6177 • Connections to FACP are power-limited and supervised • 5.160" (13.11 cm.) high x 10.043" (25.51 cm.)wide x 1.77" (4.5 cm.)deep The ANN-Bus POWERING THE DEVICES ON THE ANN-BUS FROM AUXIL- IARY POWER SUPPLY ANN-Bus devices can be powered by an auxiliary power supply when available panel power is exceeded. See FACP manual for information. ANN-BUS DEVICE ADDRESSING Each ANN-Bus device requires a unique address (ID Number) in order to communicate with the FACP.A maximum of eight devices can be connected to the FACP ANN-Bus communication circuit. See the FACP manual for more information. DF-60241:E•3/15/2018—Page 1 of 2