Laserfiche WebLink
ci FDLCO www.tolco.com <br /> abanoo-NIBCO Revision 1/21/2011 <br /> Fig. 4L C UL US LISTED <br /> Longitudinal "In-Line" Sway Brace Attachment <br /> Size Range — 21" through 8" IPS. fog <br /> Material — Carbon Steel <br /> Function — For bracing pipe against sway and seismic disturbance. �I jam' <br /> Approvals — Underwriter's Laboratories Listed in the USA (UL) and 0 <br /> Canada (cUL) 21" - 8" Approved by Factory Mutual Engineering (FM), 4 <br /> 2'h" - 8" pipe. <br /> Installation Instructions — The Fig. 4L is the "braced pipe" attachment <br /> component of a longitudinal sway brace assembly. It is intended to be D A <br /> combined with the "bracing pipe" and TOLCO structural attachment <br /> component to form a complete bracing assembly. NFPA 13 and/or <br /> OSHPD guidelines should be followed. <br /> To Install — Place the Fig. 4L over the pipe to be braced and tighten <br /> bolts. Then engage "bracing pipe" into jaw opening and tighten set bolt <br /> until hex head snaps off. Jaw attachment can pivot for adjustment to C ‘1/4L11104.1 r <br /> proper brace angle. <br /> Finish — Plain � <br /> Note — Available in Electro-Galvanized and HDG finish. <br /> Order By — Figure number, pipe size and finish. <br /> 00, N, 45r- <br /> de <br /> • o� Dimensions •Weights <br /> O <br /> , Max. Rec. *Max Design <br /> Sizes A C D Slie Load Lbs. Load Lbs. Wtprox <br /> (cULus) (FM) <br /> 1 In <br /> 100 <br /> Ii I 2�/z 6�/is 2�/z 23/a 1/2 2015 3000 253 <br /> 3 7 23/4 3'/is 1/2 2015 1550 268 <br /> 4 8'h 33/a 3"/is 1/2 2015 1550 348 <br /> o <br /> 5 93/4 37/s 43/s 1/2 2015 1450 380 <br /> Longitudinal Brace 6 111/2 5 51/8 1/2 2015 1450 640 <br /> 8 131 55/8 55/8 1/2 2015 1450 728 <br /> �� �� *The loads listed are axial loads on the brace.The horizontal load capacity,H,of the <br /> ,� `�: brace is:H=F x sin 0,where 0 the installation angle measured from the vertical. <br /> FM approved when used with 1", 11", 11/2"or 2"Sch.40 brace pipe. <br /> ii4 4/7 <br /> *11 <br /> 4-Way Riser Brace <br /> (Plan view) <br /> TOLCOe brand bracing components are designed to be compatible ONLY with other TOLCO(e)brand bracing components,resulting in a Listed seismic <br /> bracing assembly. DISCLAIMER — NIBCO does NOT warrant against the failure of TOLCO®brand bracing components, in the instance that such <br /> TOLCO®brand bracing components are used in combination with products, parts or systems which are not manufactured or sold under <br /> the TOLCO®brand. NIBCO shall NOT be liable under any circumstance for any direct or indirect, incidental or consequential damages of any kind, <br /> including but not limited to loss of business or profit,where non-TOLCO brand bracing components have been,or are used. <br /> OFFICE/MANUFACTURING FACILITY•1375 SAMPSON AVE.•CORONA,CA 92879•PH: 951.737.5599•FAX: 951.737.0330 <br /> 29 CUSTOMER SERVICE•800.786.5266 <br /> www.tolco.com <br />