3003 W CASINO RD BLDG 40-36 2025-03-25

10.04 VIC-FLANGE ADAPTER NOTES 1 The Style 744 (2 - 8'750 - 200 mm) design Incorporates small teeth Inside the key shoulder I . to prevent rotation. z FireLock Flange adapter should not be used on FireLock fittings. When wafer or lug -type valves are used adjoining a Victaulic fitting, check disc dimensions to assure proper clearance. a FireLock Flange adapters should not be used as anchor pointsfortie-rodsacross nonrestrainedjoints. Mating rubber faced flanges, valves, etcrequire the use of a FireLock Flange washer. a Area A-B noted in the above drawing must be free from gouges, undulations or deformities of any type for effective sealing. s FireLock Flange adapter gaskets must always be assembled with the color coded lip on the pipe and the other lip facing the mating flange. 6 Flange Washers FireLock Flange adapters require a smooth hard surface at the mating flange face for effective sealing. Some applications for which the Vic -Flange adapter is otherwise well suited do not provide an adequate mating surface. In such cases, it is recommended thata metal Flange Washer be inserted between the FireLock Flange adapter and the mating flange to provide the necessary sealing surface. Typical applications where a Flange Washer should be used are w When mating to a serrated flange a standard flat flange gasket should be used adjacent to the serrated flange and then the Flange Washer is inserted between the FireLock Flange adapter and the flange gasket. s When mating to a wafervalve.where typical valves are rubber lined and partially rubberfaced(smooth or not), the Flange Washer is placed between the valve and the FireLock Flange adapter. c When mating a rubber faced flange the Flange Washer is placed between the FireLock Flange adapters and the rubber faced flange. D When mating AWWA cast flanges to IPS flanges. the Flange Washer is placed between two FireLock Flanges. The hinge points must be oriented approximately 90' to each other. If one flange is not a FireLock Flange adapter (e.g. flanged valve), then a standard flat flange gasket must be placed adjacent to that flange and the Flange Washer inserted between the flange gasket and the FireLock Flange adapter. e When mating to components (valves, strainers, etc ) where the component flange face has an Insert. follow the same arrangement as in Application 1. F When mating to a Series 705-W Butterfly valve, Style 744 may only be used on one side of the connection. When ordering Flange Washers, always specify product style (Style 744) and size to assure proper Flange Washer is supplied MATERIAL SPECIFICATIONS Flange Housing. Ductile iron conforming to ASTM A-536, grade 65-45-12. Ductile iron conforming to ASTM A-395, grade 65-45-15, is available upon special request. Coating: Black enamel • Optional: Hot dipped galvanized Bolts/Nuts: Supplied by installer Gasket: • Grade "E" EPDM - Type A Vic -Plus Gasket System A (Violet color code). FireLock products have been Listed by Underwriters Laboratories Inc. and Ap- proved by Factory Mutual Research for wet and dry (oil free air) sprinkler services up to the rated Work- ing pressure using the Grade "E" Type A Vic -Plus Gasket System, requiring no field lubrication for most installation conditions. A Standard gasket approved for dry pipe systems to -400F T400C). Based on `typical" pipe surdce conditions, supplemental lubricant is recommended for services insta Iled below 0° F (-18°C) and for a II d ry pipe systems or systems to be subjected to a it tests prior to being filled with water. Su p p lementa I lubrication maya Iso be rquire d on pipe with raised or undercutwe Id sea ms or pipe that has voids and/or cracks at the weld seams. This product shall be manufactured by actau lic Company. All products to be installed in accordance with current actaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. Style 744 FireLock® Flange Adapter