Laserfiche WebLink
Fig. 4L C&US LISTED <br />Longitudinal "In -Line" Sway Brace Attachment FM <br />APPROVED <br />Size Range — 21/2" through 8" IPS. <br />Material — Carbon Steel <br />Function — For bracing pipe against sway and seismic disturbance. <br />Approvals — Underwriter's Laboratories Listed in the USA (UL) and <br />Canada (cUL) 21/2" - 8". Approved by Factory Mutual Engineering (FM), <br />21/2" - 8" pipe. <br />Installation Instructions — The Fig. 4L is the "braced pipe" attachment <br />component of a longitudinal sway brace assembly. It is intended to be <br />combined with the "bracing pipe" and TOLCO structural attachment <br />component to form a complete bracing assembly. NFPA 13 and/or <br />OSHPD guidelines should be followed. <br />To Install — Place the Fig. 4L over the pipe to be braced and tighten <br />bolts. Then engage "bracing pipe" into jaw opening and tighten set bolt <br />until hex head snaps off. Jaw attachment can pivot for adjustment to <br />proper brace angle. <br />Finish — Plain <br />Note — Available in Electro-Galvanized and HDG finish. <br />Order By — Figure number, pipe size and finish. <br />Longitudinal Brace <br />4-Way Riser Brace <br />(Plan view) <br />Dimensions • Weights <br />Max. Rec. <br />Max Design <br />Sizes <br />A <br />C <br />D <br />Bolt <br />Load Lbs. <br />Load Lbs. <br />Approx. <br />Size <br />(cULus) <br />(FM) <br />Wt/100 . <br />/100 <br />21/2 <br />67/16 <br />21/2 <br />23/4 <br />1 /2 <br />2015 <br />3000 <br />253 <br />3 <br />7 <br />23/4 <br />31/16 <br />1 /2 <br />2015 <br />1550 <br />268 <br />4 <br />81/2 <br />33/8 <br />311/16 <br />1 /2 <br />2015 <br />1550 <br />348 <br />5 <br />93/4 <br />37/8 <br />43/8 <br />1 /2 <br />2015 <br />1450 <br />380 <br />6 <br />111/2 <br />5 <br />51/8 <br />1 /2 <br />2015 <br />1450 <br />640 <br />8 <br />131/4 <br />55/8 <br />55/8 <br />1 /2 <br />2015 <br />1450 <br />728 <br />* The loads listed are axial loads on the brace. The horizontal load capacity, H, of the <br />brace is: H = F x sin 0, where 0 the installation angle measured from the vertical. <br />FM approved when used with 1 ", 11/4", 11/2" or 2" Sch. 40 brace pipe. <br />TOLCO® brand bracing components are designed to be compatible ONLY with other TOLCO® brand bracing components, resulting in a Listed seismic <br />bracing assembly. DISCLAIMER — NIBCO does NOT warrant against the failure of TOLCO® brand bracing components, in the instance that such <br />TOLCO® brand bracing components are used in combination with products, parts or systems which are not manufactured or sold under <br />the TOLCO® brand. NIBCO shall NOT be liable under any circumstance for any direct or indirect, incidental or consequential damages of any kind, <br />including but not limited to loss of business or profit, where non-TOLCO brand bracing components have been, or are used. <br />m OFFICE/MANUFACTURING FACILITY • 1375 SAMPSON AVE. • CORONA, CA 92879 • PH: 951.737.5599 • FAX: 951.737.0330 <br />CUSTOMER SERVICE • 800.786.5266 <br />www.tolco.com <br />