3224 RUCKER AVE 2025-03-25 - Laserfiche WebLink

MASTER CONTRACT: 266909 MASTER CONTRACT: 266909 BLUE RAVEN REPORT: 70131735 Page No: 6 REPORT: 70131735 Page No: 9 PROJECT: 80136577 Date Issued:August 12,2022 PROJECT: 80136577 Date Issued:August 12,2022 1403 N.Research Way Orem,UT 84097 800.377.4480 WWW.BLUERAVENSOLAR.COM SM and ULA markings 1. The system does not employ a maximum number of modules that can be installed per system. CONFIDENTIAL-THE INFORMATION Y P Y p Y HEREIN CONTAINED SHALL NOT BE The following markings appear on the rail by adhesive label: 2. Module Orientation: USED FOR THE BENEFIT OF ANYONE a. SM&ULA-Portrait OY LandSCa e EXCEPT BLUE RAVEN SOLAR NOR Il SHALL IT BE DISCLOSED IN WHOLE OR I. Submitter's name and/or CSA Master Contract number"266909"; b. RM5&DT—Landscape IN PART TO OTHERS OUTSIDE 2. Model designation; a. GFT—Portrait ECIPIENTS CO CONNECTION WITH THIE ON SALE EXCEPT N AND 3. Manufacturing date; d. NXT Horizon-Portrait or Landscape USE OF THE RESPECTIVE EQUIPMENT, was evaluated for use with modules stem u WITHOUT THE WRITTEN PERMISSION 4. System fire class rating/designation of information location in Installation Manual; 3. The system p to: OF BLUE RAVEN SOLAR LLC. 5. Design load rating/designation of information location in Installation Manual; a. SM&ULA—27.12 sq ft b. RM5&DT—27.76 sq ft The following markings appear on the Mid clamp by stamping: c. GFT-Portrait-27.12 sq ft NABCEP d. NXT Horizon—27.76 sq ft C E RT I F I E D 1. Submitter's name and/or CSA Master Contract number"266909"; 4. See Table 1 for customer supplied information for SM 2. CSA mark 5. See Table 2 for customer supplied information for ULA PV INSTALLATION 3. Mil ID for factory location 6. See Table 3 for customer supplied information for RM PROFESSIONAL 7. See Table 4 for customer supplied information for GFT Scott Gurney 8. See Table 5 for customer supplied information for NXT Horizon #PV-011719-015866 Nameplate adhesive label material approval information: 9. See the attached installation manual for each model installation instructions,and system drawings. CONTRACTOR: SATO AMERICA INC,SF401 DuraMark Polyester,MH48415 -Printing Materials—Component,UL 969- The critical components identified below may be formed at other locations and shipped directly BRS FIELD OPS Marking and Labeling Systems to the construction site provided they are made with the material/coatings identified and conform 385-498-6700 to the physical dimensions described and shown in their respective illustrations.Physical RM 5 South and RM DT markings specimens may not be present at the location where the CSA mark is applied. Location of markings can be found in the Marking section of this report. The following markings appear on the ballast bay by permanent stamping: 1. Submitter's name and/or CSA Master Contract number"266909"; Table 1 2. Model designation; 3. Manufacturing date; MODULE RACKING SYSTEM TYPE/S 4. System fire class rating/designation of information location in Installation Manual; Model SM 5. Design load rating/designation of information location in Installation Manual; Module Fire Type.............................: Class A with Type 1,2,3 (with metallic frame),4(with trim), 5 (with trim), 10(with metallic frame), 19,22,25,29,or 30 for steep slope.Tested at 5"interstitial gap,the rating obtained for a 7"ACR 5-inch(127 mm)gap can be used for any other gaps allowed by UNIRAC RM SOUTH 5 the mounting instructions,per section 15 ofUL 2703 CONFORMS TO UL STD 2703 p Max branch circuit overcurrent- 30 PATENT PENDING protection device(A) UNIRAC MFR DDDYYP COWOIM C U S IDENTIFICATION OF COMPONENTS AND MATERIALS UWACMR End Clam M101XX Rev.H 266909 Extruded Aluminum:6005A-T61,6351-T5,6061-T6,6005-T5, DRAWING BY: SYSTEM FIRE CUSS RATING:SEE INSTALUITION INSTRUCTIONS FOR INSTALLATION REQUIREMENTS TO ACHIEVE A 6105-T5 SPECIFIED SYSTEM FIRE CLASS RATING WRH THIS PRODUCT. Clwlmgiis wnat DESIGN LOAD HATING:SEE INSTALLATION INSTRUCTIONS FOR LOADS AND MODULES QUALIFIED FOR USE WITH THIS End Clam ON ASSembl MSOOXX Rev. C,(M50060—M50071) PRODUCT. Y Y.......................: Extruded Aluminum:6005A-T61,6351-T5,6061-T6,6005-T5, PLOT DATE: 6105-T5 Nameplate adhesive label material approval information: Bonding Mid Clamp.........................: M6065X,Rev A and M6065X,Rev F Markings applied via permanent stamping to bay. 300 Series Stainless Steel PROJECT NUMBER: SHEET NAME: SPEC SHEET DQD 507.10 Rev 2022-08-05 ©2022 CSA Group. All rights reserved. DQD 507.10 Rev 2022-08-05 ©2022 CSA Group. All rights reserved. REVISION: PAGE NUMBER: -___ SS