Laserfiche WebLink
Model W2 (upright, pendent) <br />Model J (New frame with guard installed) <br />Model JD (Legacy frame with guard installed, similar but with zinc finish) <br />Finishes') <br />Standard Finishes <br />Special Application Finishes <br />Sprinkler <br />F1, F2 and FP(2) <br />Escutcheons <br />CCP Cover <br />Plate(2) <br />Sprinkler <br />p <br />F1, F2 and FP(2) <br />Escutcheons <br />CCP Cover Pllte(2) <br />„a <br />Bronze <br />Brass <br />Chrome <br />Electroless Nickel PTFE3)(4) <br />Bright Brass <br />Bright Brass <br />Chrome <br />Chrome <br />White Paint <br />Bright Brass(5) <br />Satin Chrome <br />Satin Chrome <br />White Polyester(l) <br />White Polyester <br />Satin Chrome <br />Custom Color Polyester <br />Custom Color Paint <br />Custom Color Polyester(3) <br />Notes: <br />Paint or any other coating applied over the factory finish will void all approvals and warranties. <br />Model FP escutcheons and Model CCP sprinklers utilize a galvanized steel cup with a finished trim ring or cover plate. <br />c1JLus Listed as corrosion resistant. <br />FM Approved as corrosion resistant. <br />For 200°F (93°C) maximum temperature rated sprinklers only. <br />Installation <br />Model F1 FIR Series sprinklers must be installed in accordance with <br />NFPA13 and the requirements of all applicable authorities having <br />jurisdiction. Model F1 FIR Series sprinklers must be installed with <br />the Reliable sprinkler installation wrench identified in this Bulletin. <br />Any other wrench may damage the sprinkler. The Models W2 and <br />W4 wrenches have two sets of jaws. Use the smallest set of jaws <br />that fit on the wrench flats of the sprinkler. A leak tight sprinkler <br />joint can be obtained with a torque of 8 to 18 lb-ft (11 to 24 <br />N•m). Do not tighten sprinklers over the maximum recommended <br />installation torque. Exceeding the maximum recommended <br />installation torque may cause leakage or impairment of the <br />sprinkler. <br />Glass bulb sprinklers have orange bulb protectors or protective <br />caps to minimize bulb damage during shipping, handling and <br />installation. Reliable sprinkler installation wrenches are designed <br />to install sprinklers with bulb protectors in place. Remove the bulb <br />protector at the time when the sprinkler system is placed in service <br />for fire protection. Removal of the bulb protector before this time <br />may leave the bulb vulnerable to damage. Remove bulb protectors <br />by undoing the clasp by hand. Do not use tools to remove bulb <br />protectors. <br />Maintenance <br />Reliable Model F1 FIR series sprinklers should be inspected and <br />the sprinkler system maintained in accordance with NFPA 25, as <br />well as the requirements of any Authorities Having Jurisdiction. <br />Prior to installation, sprinklers should remain in the original <br />cartons and packaging until used. This will minimize the potential <br />for damage to sprinklers that could cause improper operation or <br />non -operation. <br />Do not clean sprinklers with soap and water, ammonia liquid or <br />any other cleaning fluids. Remove dust by gentle vacuuming <br />without touching the sprinkler. <br />Replace any sprinkler which has been painted (other than factory <br />applied). A stock of spare sprinklers should be maintained to <br />allow quick replacement of damaged or operated sprinklers. <br />Failure to properly maintain sprinklers may result in inadvertent <br />operation or non -operation during a fire event. <br />Bulletin 074 Page 8 of 9 <br />January 2023 www.reliablesprinkler.com <br />