5901 23RD DR W ZAP ENERGY 2025-04-23

DN-6720:E FMM-1 (A), FMM-101 (A), N QT I F I E RJ FZM 1 A & FDM Monitor Modules with FlashScan® by Honeywell �a I Intelligent/Addressable Devices; General Four different monitor modules are available for Notifier's intelligent control panels for a variety of applications. Monitor modules supervise a circuit of dry contact input devices, i such as conventional heat detectors and pull stations, or > monitor and power a circuit of two-wire smoke detectors ® ,M (FZM-1(A)). _. ' FMM-1(A) is a standard-sized module (typically mounts to a 4" [10.16 cm] square box) that supervises either a Style D wt t 1 t kf2��" (Class A) or Style B (Class B) circuit of dry-contact input 1 •A$} devices. r ; FMM-101(A) is a miniature monitor module a mere 1.3" � ', L (3.302 cm)H x 2.75"(6.985 cm)W x 0.65"(1.651 cm)D that Ili 07. supervises a Style B (Class B) circuit of dry-contact input devices. Its compact design allows the FMM-101(A) to be e `/ mounted in a single-gang box behind the device it monitors. to I. FZM-1(A) is a standard-sized module that monitors and supervises compatible two-wire, 24 volt,smoke detectors on > a Style D(Class A)or Style B(Class B)circuit. FMM-1(A)(Type H) FDM-1(A)is a standard-sized dual monitor module that mon- itors and supervises two independent two-wire Style B(Class open dry-contact alarm activation devices. May also be used B)dry-contact initiating device circuits(IDCs)at two separate, to monitor normally-open supervisory devices with special consecutive addresses in intelligent,two-wire systems. supervisory indication at the control panel. Monitored circuit FlashScan® (U.S. Patent 5,539,389) is a communication may be wired as an NFPA Style B(Class B)or Style D(Class protocol developed by NOTIFIER that greatly increases the A) Initiating Device Circuit. A 47K Ohm End-of-Line Resistor speed of communication between analog intelligent devices. (provided) terminates the Style B circuit. No resistor is Intelligent devices communicate in a grouped fashion. If one required for supervision of the Style D circuit. of the devices within the group has new information, the FMM-1(A) OPERATION panel CPU stops the group poll and concentrates on single points. The net effect is response speed greater than five Each FMM 1(A)uses one of the available module addresses times that of other communication protocols. on an SLC loop. It responds to regular polls from the control panel and reports its type and the status(open/normal/short) FMM-1(A) Monitor Module of its Initiating Device Circuit(IDC). A flashing LED indicates that the module is in communication with the control panel. • Built-in type identification automatically identifies this The LED latches steady on alarm (subject to current limita- device as a monitor module to the control panel. tions on the loop). • Powered directly by two-wire SLC loop. No additional FMM-1(A) SPECIFICATIONS power required. • High noise(EMF/RFI)immunity. • SEMS screws with clamping plates for ease of wiring. Maximum current draw: 5.0 mA(LED on). • Direct-dial entry of address:01 —159 on FlashScan loops; Average operating current: 375 pA(LED flashing), 1 com- 01 —99 on CLIP loops. munication every 5 seconds,47k EOL. • LED flashes green during normal operation (programma- bleoption)and latches on steady red to indicate alarm. Maximum IDC Voltag The FMM-1(A) Monitor Module is intended for use in intelli- gent,two wire systems,where the individual address of each EOL resistance:47K Ohms. module is selected using the built-in rotary switches. It pro- Temperature range: 32°F to 120°F(0°C to 49°C). vides either a two-wire or four-wire fault-tolerant Initiating Device Circuit(IDC)for normally-open-contact fire alarm and Humidity range: 10%to 93%noncondensing. supervisory devices.The module has a panel-controlled LED Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x indicator. The FMM-1(A) can be used to replace MMX-1(A) 1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x modules in existing systems. 2.125"(5.398 cm)deep box. FMM-1(A)APPLICATIONS Use to monitor a zone of four-wire smoke detectors, manual fire alarm pull stations, waterflow devices, or other normally- DN-6720:E•07/30/2015—Page 1 of 4