Laserfiche WebLink
Anchor Fastening Technical Guide,Edition 22 <br /> MATERIAL SPECIFICATIONS' <br /> For material specifications for anchor rods and inserts, please refer to section 3.2.8. <br /> DESIGN DATA IN CONCRETE PER ACI 318 <br /> ACI 318 Chapter 17 design <br /> The load values contained in this section are Hilti Simplified Design Tables.The load tables in this section were developed <br /> using the Strength Design parameters and variables of ESR-4868 and the equations within ACI 318 Chapter 17. For a detailed <br /> explanation of the Hilti Simplified Design Tables, refer to section 3.1.8. Data tables from ESR-4868 are not contained <br /> in this section, but can be found at www.icc-es.org or at www.hilti.com. <br /> HIT-HY 200 V3 adhesive with HIT Z and HIT Z-R anchor rods <br /> . I <br /> Figure 1 —Hilti HIT-Z and HIT Z-R installation conditions <br /> Hammer drilling with carbide <br /> o � tipped drill bit' <br /> a) - Uncracked o° °° Dry = PP <br /> concrete °°�°° concrete a5i o <br /> g ID - C—t Hilti TE-CD or TE-YD Hollow <br /> E a) -a E Drill Bit 2 <br /> �, Cracked o o Water-saturated <br /> a. c concrete °o o° concrete a �� Diamond core drill bit 3 <br /> CJ o , <br /> 1 Anchor may be installed in a hole drilled with a carbide-tipped bit without cleaning the drilling dust from the hole. Temperature must be 41°For higher. <br /> Drilling dust must be removed from the hole if the temperature is below 41°F.See Manufacturer's Published Installation Instructions(MPH). <br /> 2 When temperatures are below 41°F,TE-CD or TE-YD Hollow Drill Bits used with a Hilti vacuum cleaner are viable methods for removing drilling dust from the hole. <br /> 3 Holes drilled by diamond coring require cleaning with a water hose and compressed air. See MPH. <br /> Table 1 —Specifications for Hilti HIT Z and HIT-Z-R installed Figure 2 — Hilti HIT Z and HIT Z-R <br /> with Hilti HIT HY 200 A/R V3 adhesive specfications <br /> Nominal anchor diameter hef ►I <br /> Setting information Symbol Units ■' <br /> 3/8 1/2 5/8 3/4 <br /> Nominal bit diameter do in. 7/16 9/16 3/4 7/8 do,IM_____MMIIII�������������������I��I��I� I�I������I�I���I���� I <br /> in. 2-3/8 2-3/4 3-3/4 4 t ■ <br /> minimum hef,mm <br /> Effective (mm) (60) (70) (95) (102) <br /> embedment in. 4-1/2 6 7-1/2 8-1/2 <br /> maximum hetma. Figure 3— <br /> (mm) (114) (152) (190) (216) <br /> Installation with(2)washers <br /> through-set in. 1/2 5/8 13/161 15/161 - <br /> Diameter <br /> of fixture hole <br /> preset 4 in. 7/16 9/16 11/16 13/16 - <br /> 4- <br /> ft-lb 15 30 60 110 <br /> HIT-Z Test <br /> (Nm) (20) (40) (80) (150) <br /> Installation torque <br /> ft-lb 30 65 125 165 <br /> HIT-Z-R T,�t <br /> (Nm) (40) (90) (170) (220) <br /> 1 Install using(2)washers.See Figure 3. <br /> Anchor Fastening Technical Guide Edition 22 13.0 ANCHORING SYSTEMS 13.2.2 HILTI HIT-HY 200 A/R V3 23 <br /> Hilti,Inc.1-800-879-8000 I en espanol 1-800-879-5000 I www.hilti.com I Hilti(Canada)Corporation I www.hilti.ca 11-800-363-4458 <br />