9920 18TH AVE W C 2025-04-07 - Laserfiche WebLink

Cover Plate FinishesM - Standard Finishes Special Application Finishes White Polyester Off White Paint Black Paint Raw Brass Chrome Plated Bright Brass Finished Bronze Black Plated Satin Chrome Stainless Steel Clad(3) Custom Color Paint(2) Notes: 1. Paint or any other coating applied over the factory finish will void all approvals and warranties. 2. Custom color paint is semi-gloss,unless specified otherwise. 3. Stainless steel clad cover plates are Type 316 Stainless Steel on the finished side and C102 Copper Allow on the backside.Cover plates are not listed or approved as corrosion resistant.Stainless steel clad cover plates are not available perforated. Installation Dimensions Recommended Min.to Min.to Max. Sprinkler Cover Cover Plate Hole Diameter Cover Plate Max. Face Dropped Deflector Cover Plate Plate Diameter Adjustment of Fitting to Distance below Temperature Model Model inch(mm) in Ceiling inch (mm) Ceilings') Ceiling Rating inch(mm) inch(mm) inch(mm) RFC30, 3-5/16 2-5/8 1/2 1-1/2 to 2 1/2 to 1 1350F RFC30LL RFC (84) (67) (13) (38 to 51) (13 to 25) (57°C) RFC43, 1350F(2) RFC43LL, RFC 3-5/16 2-5/8 1/2 1-1/2 to 2 1/2 to 1 (57°C) RFC49, (84) (67) (13) (38 to 51) (13 to 25) or 1650F3 RFC49LL (74°C) 1350F(2) RFC58, RFC 3-5/16 2-5/8 3/4 1-1/2 to 2-1/4 1/4 to 1 (57°C) RFC76 (84) (67) (19) (38 to 57) (6 to 25) or 1650F3 (74°C) Notes: 1. Face of fitting to ceiling dimensions are based on a nominal thread make up.Verify dimensions based on fitting and thread sealing method prior to installation.A 1/2"x 1/2"brass nipple extension(Reliable P/N 6999991900)is available where necessary for replacement of existing sprinklers. 2. For use with 165°F(74°C)temperature rated sprinklers where the Maximum Ceiling Temperature does not exceed 100°F(38°C). 3. For use with 212°F(100°C)temperature rated sprinklers where the Maximum Ceiling Temperature does not exceed 150°F(66°C). Installation Model RFC series sprinklers are intended to be installed in ac- Do not exceed the maximum recommended torque. Exceeding cordance with NFPA 13, NFPA 13R,or NFPA 13D,as well as the the maximum recommended torque may cause leakage or im- requirements of applicable authorities having jurisdiction. Mod- pairment of the sprinkler. Use care when inserting or removing el RFC series sprinklers must not be installed in ceilings with the wrench from the sprinkler to avoid damage to the sprinkler. positive pressure in the space above. Ensure that the 4 slots in the cup are open and unobstructed following installation. Model Install the cover plate by hand by pushing the cover plate into RFC series sprinklers are shipped with a wrench-able protec- the cup and turning the cover in the clockwise direction until it tive cap that should remain on the sprinkler until the sprinkler is tight against the ceiling. system is placed in service following construction. Model RFC series sprinklers can be installed without removing Application the wrench-able protective cap using the Model W3 wrench. Model RFC series sprinklers are intended for installation where Alternatively, Model RFC series sprinklers can be installed us- residential sprinklers are permitted or required by NFPA 13, ing the Model FC wrench by temporarily removing the protec- NFPA 13R, and NFPA 13D. The sprinklers are concealed pen- tive cap during installation of the sprinkler.The use of any other dent residential sprinklers. wrench to installed Model RFC series sprinklers is not permit- ted and may damage the sprinkler. Fully insert the Model W3 Model RFC 30 and RFC30LL sprinklers are available in ordinary wrench over the cap until it reaches the bottom of the cup, or temperature classification for installation where the Maximum the Model FC wrench over the sprinkler until the wrench engag- Ceiling Temperature does not exceed 100OF (380C). Model es the body. Do not wrench any other part of the sprinkler/cup RFC43, RFC43LL, RFC49, RFC49LL, RFC58,and RFC76 sprin- assembly.The Model W3 and FC wrenches are designed to be klers are available in either ordinary or intermediate tempera- turned with a standard 1/2" square drive. Tighten the sprinkler ture classification for installation where the Maximum Ceiling into the fitting after applying a PTFE based thread sealant to the Temperature does not exceed 100OF (38°C) or 150OF (660C), sprinkler's threads. Recommended installation torque is 8 to 18 respectively. ft-Ibs(11 to 24 N-m)for 1/2"thread sprinklers and 14 to 20 ft-Ibs (19 to 27 N-m)for 3/4"thread sprinklers. Bulletin 006 Reliably Page 7 of 8 May 2019 www.reliablesprinkler.com