906 SE EVERETT MALL WAY AINSWORTH INC 2025-04-08

Wiring & Configuration Signature device loop Auxiliary&smoke power outputs(TB3) The system provides one Signature device loop circuit with a total The control panel provides two auxiliary power TB3 capacity of 125 detectors and 125 module addresses.The loop outputs that can be used for powering ancillary circuit is supervised for opens, shorts, and grounds. equipment such as remote annunciators and two No (1)wire smoke detectors. Aux 2 can be software � NC Circuit i01000 i064 selected to operate continuously.The circuit is specifications Device loops One Class B or A One Class B or A loop, supervised for shorts and grounds. loop,supporting125 supporting 64 devices of (2) NO pp 9 Circuit specifications detectors and 125 any kind. Circuit voltage 21.9 to 28.3 V modules.Expandable to range (2) NC four loops. I Resettable circuit 24 VDC nominal at 500 mA (3) Communication Maximum 20 V peak-to-peak (Aux power 2) NO line voltage Continuous circuit 24 VDC nominal at 500 mA. Circuit current 0.5 A max (Aux power 1) Use this circuit for powering Q Circuit 660 total,0.5 NF,max two-wire smoke detectors. impedance (4) 0 Isolators 64 maximum Note:Any current above 0.5 amp connected to both Aux 1 and 2 will reduce the total available NAC power by that O Signal Supported on a system-wide basis(all device loops) amount. Synchronization when using a SIGA-CC1 S or SIGA-MCC1 S module (1)Trouble and Genesis or Enhanced Integrity notification ap- Alarm trouble and supervisory Perviso rY relay(TB3)) (2)Supervisory The trouble relay is normally-open, held closed, (3)Alarm Class a wiring Class A wiring and opens on any trouble event or when the panel is de-energized.The supervisory relay is (4)Smoke/Aux SLC A Data Line SLC A normally-open,and closes on any supervisory + + + + event.The alarm relay changes over on any SLC B + SLC B +� alarm event. Loop Loop Loop Loop Loop card device device Loop card Data Line device device Relay specifications Alarm Trouble Supervisory Type Form C Form A Notification appliance circuits(TB2) Voltage 24 VDC at 1 A resistive 24 VDC at 1 A resistive i01000 control panels come equipped with four notification ap- Relay circuits can only be connected to power-limited sources. pliance circuits. i064 control panels come with two NACs. Each circuit can be individually configured for continuous,temporal, synchronized, and coded output. Annunciator loop(TB4) Specifications i01000 i064 The control panel provides a connection for up to eight serially Circuit Type 4 Class B or 2 Class A 2 Class B or 2 Class A driven and supervised remote annunciators. with SA-CLA module Voltage 24 VFWR Circuit specifications Current 6.0 A total,2.5 A max. 3.75 A total,2.5 A max. Device loops Class B(Style Y)or Class A(Style 2) per circuit at 120/230 per circuit at 120/230 Circuit voltage 2.55 V VAC 60 Hz. VAC 60 Hz. Circuit current 30 mA max 5.0 A total,2.5 A max. 3.0 A total,2.5 A max. Circuit Up to 8 annunciators or 4000 feet per circuit at 230 VAC per circuit at 230 VAC impedance 50 Hz. 50 Hz. Impedance 26 n total,0.35 pF max Class B Class A EOLR 15 K O,1/2 W Channel 1 Channel 2 Channel 1 Channel 2 Synchronization Supported system-wide + — + — + — + — & TB4 TB4 Class a wiring Class A wiring Annunciator Annunciator • NAC1- + + (2) NAC1- + + CH1(+)IN CH1(+)IN • NAC1+ _ - EOLR o NAC1+ - - CH1(-)IN CH1(-)IN NAC2- + / + 0 NAC2- + + NAC2+ - V - a NAC2+_00 Ta2 Tat CH2(+)IN CH2(+)IN 0 NAC3- + + - CH2(-)IN CH2(-)IN o NAC3+ - - + NAC4- + EOLR _ + NAC4+ < 13 + TB6 TB6 Marking indicates output signal polarity when the circuit is active.Polarity reverses when the circuit is not active.Wire notification appliances accordingly.Notification appliance polarity shown in active state. Page 4 of 8 DATA SHEET E85001-0135 Not to be used for installation purposes. Issue 1