1509 CALIFORNIA ST DAWSON PLACE 2025-04-07

K II GENERAL SPECIFIC • 1.01 WORK INCLUDED 1.06 SUBMITTALS A.Unispan System shall be furnished,installed and serviced by A.Manufacturer shall provide prior to fabrication written KWIK-WALL's authorized distributor,in compliance with the technical information and related detail shop drawings,which architectural drawings and specifications contained herein. demonstrate that the products comply with contract documents. Include elevations,sections,and details.Indicate dimensions, 1.02 RELATED WORK weights,conditions at openings and at storage areas. A.Opening Preparation: Proper and complete preparation of the Unispan system opening shall be by others in accordance B.KWIK-WALL shall provide detailed engineering drawings with ASTM E 557,and shall include floor leveling;plumbness featuring track plan,panel elevation,horizontal and vertical of adjoining permanent walls;substrate and/or ceiling tile details and beam punching template as required. enclosures for the Unispan system;and the painting C.KWIK-WALL shall provide written instructions specifying the and finishing of trim and other materials adjoining the head and proper operation and maintenance of the operable wall system. jamb areas of the operable wall.Any deviation of site conditions contrary to approved shop drawings must be called to the attention of the architect. 1.07 DELIVERY,STORAGE AND HANDLING B.Insulation:Sound insulation and baffles for the plenum area A.Panels shall be individually wrapped in a protective plastic above the track system,under the permanent floor,inside air covering to keep panels clean during delivery,storage ducts passing over or around the operable wall,and in permanent and handling. walls adjoining the operable wall system shall be by others,in B.Truss system shall be shipped in sections and assembled on site. accordance with ASTM E 557. C.Panels shall be stored on edge and above the floor on cushioned C.Opening Preparation:Proper and complete preparation of the blocking in a dry and ventilated area,protected from humidity operable wall system opening shall be by others in accordance and temperature extremes. with ASTM E 557,and shall include floor leveling;plumbness of adjoining permanent walls;and the painting and finishing 1.09 WARRANTY of trim and other materials adjoining the head and jamb areas of the operable wall. A.Manufacturer shall warrant each Unispan system and its component parts to be free from defects in material and 1.03 SYSTEM DESCRIPTION workmanship for a period of ten(1o)years from the date of delivery A.The Unispan system is a self-supporting truss system for use to the original purchaser when installed by an authorized KWIK- with operable partitions. WALL distributor. (Contact your local KWIK-WALL Distributor or KWIK-WALL Company for complete warranty information.)(see 1.04 QUALITY ASSURANCE actual warranty on Page 8 for details and limitations). A.The Unispan system shall be validated by calculations performed by a licensed professional engineer. B.The Unispan system shall be installed by KWIK-WALL's authorized distributor in accordance with ASTM E 557• 1.05 REFERENCES A.ASTM E go:Laboratory Measurement of Airborne-Sound Transmission Loss of Building Partitions. B.ASTM E 413:Determination of Sound Transmission Class(STC). C.ASTM E 557:Architectural Application and Installation of Operable Partitions. D.ASTM E 84:Surface Burning Characteristics of Building Materials. E.ASTM A 653:Specification for General Requirements for Steel Sheet,Alloy-Coated(Galvannealed)by the Hot Dip Process. F.ASTM C 423:Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method. G.CCC-W-4o8A:Federal Specification which applies to Vinyl Coated Wall Coverings. H.CFFA-W-ioi-D:Chemical Fabrics and Film Association Quality Standard for Vinyl Coated Fabric Wall Coverings. 2 Dimensions in[I are millimeters.Contact your local distributor for additional assistance or visit www.kwik-wall.com 12-23