Laserfiche WebLink
i <br /> ! <br /> all <br /> I <br /> & ��G vds OLPCB <br /> O vNIIPo <br /> STYLES 920 AND 920N <br /> i <br /> C E �A <br /> Victaulic Mechanical-r Outlet provides a direct branch connection at any location a hole can EN 10311 IDS EN 10311 <br /> be cut in pipe.The hole is cut oversize to receive a"holefinder"locating collar which secures CPR(EUI CPR(UK) <br /> the outlet in position permanently.A pressure responsive gasket seals on the pipe O.D, No.305/2011 2019 No.465 <br /> SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS <br /> Cross-type connections can be achieved by utilizing two upper housings of the same style and <br /> size,with the same or differing branch size connections.NOTE:Style 920 and Style 920N <br /> housings cannot be mated to each other to achieve a cross connection. <br /> Style 920 and Style 920N Mechanical-T outlets are available with grooved or female threaded <br /> outlet.Specify choice on order.Units are supplied painted with plated bolts.Galvanized hous- <br /> ings are available,supplied with plated bolts. i <br /> ! <br /> All sizes of Style 920 and 920N are rated at 500psi/345OkPa working pressure on Schedule <br /> 10 and 40 carbon steel pipe.They may also be used on high density polyethylene or poly- <br /> butylene(HDPE)pipe.Pressure ratings on HDPE are dependent on the pipe rating.Contact <br /> Victaulic for ratings on other pipe.Style 920 and 92ON are not recommended for use on STYLES 920 AND 920N STYLE 920 CROSS i <br /> PVC plastic pipe. PATENTED i <br /> Standard piping practices dictate that the Mechanical-T Styles 920 and 920N must be <br /> installed so that the main and branch connections are a true 90'angle when permanently <br /> attached to the pipeline surface. <br /> Additionally,the Vic Tap II®hole Cutting tool,which allows for hole cutting capabilities on pressurized <br /> systems,utilizes the Style 920 Mechanical-T in conjunction with the Series 726 Vic-Bail Valve to <br /> create the Style 931 Vic Tap II Mechanical T unit.See page 8 for further information. <br /> i <br /> MATERIAL SPECIFICATIONS Housing/Coating:Ductile iron conforming to ASTM A-536,grade 65-45-12,with orange enamel <br /> coating,Ductile iron conforming to ASTM A-395,grade 65-45-15,is available upon special <br /> request. <br /> • Optional:Hot dipped galvanized <br /> Gasket:(Specify choice*) <br /> • Grade"E"EPDM <br /> EPDM(Green color code),Temperature range—30•F to+230°F/-34*C to+110°C. <br /> Recommended for cold and hot water service within the specified temperature range plus a <br /> variety of dilute acids,oit-free air and many chemical services.UL Classified in accordance <br /> with ANSI/NSF 61 for cold+86*F/+30°C and hot+180°F/+82*C.NOT RECOMMENDED FOR <br /> PETROLEUM SERVICES. <br /> i <br /> • Grade"T"nitrite 3 <br /> Nitrite(Orange color code).Temperature range—20*F to+180°F/-291C to+82°C. 1 <br /> Recommended for petroleum products,air with oil vapors,vegetable and mineral oils within the <br /> specified temperature range.Not recommended for hot water services over+150°F/+66'C or <br /> for hot dry air over+140°F/+600C. <br /> 'Services listed are General Service Recommendations only.It should be noted that there are <br /> services for which these gaskets are not recommended.Reference should always be made to <br /> the latest Victaulic Gasket Selection Guide for specific gasket service recommendations and for a I <br /> listing of services which are not recommended. i <br /> Bolts/Nuts:Heat-treated plated carbon steel,trackhead meeting the physical and chemical <br /> requirements of ASTM A-449 and physical requirements of ASTM A-183. j <br /> i <br /> I <br /> ! <br /> JOB/OWNER CONTRACTOR ENGINEER <br /> System No, Submitted By Spec Sect Para <br /> Location Date Approved <br /> Date <br /> www.victaulic.com <br /> VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.®2022 VICTAUL#C COMPANY.ALL RIGHTS RESERVED. r C_,-, I+C` <br /> REV P 11.021 <br />