Laserfiche WebLink
L-SERIES SPECIFICATIONS ARCHITECT/ENGINEER SPECIFICATIONS <br />GENERAL <br />L-Series standard horns, strobes, and horn strobes shall mount to a standard 2 x4 x 1 7/8-inch back box, 4.4. 11h-inch back box, <br />4-inch octagon back box, or double -gang back box. L-Series compact products shall mount to a single -gang 2.4. 1 7/8-inch back <br />box. A universal mounting plate shall be used form ounting ceiling and wall products for all standard models and a separate universal <br />mounting plate shall be used for mounting wall compact models. The notification appliance circuit wiring sha llterminate at the <br />universal mounting plate. Also, L-Series products, when used with the Sync•CircuitT" Module accessory, shall be powered from a non - <br />coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync•Circu it Module, <br />12-volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24-volt-rated notification appliance <br />circuit outputs shall operate between 16.5 and 33 volts. Indoor L-Series products shall operate between 32 and 120 degrees <br />Fahrenheit from a regulated DC or full -wave rectified unfiltered power supply. Strobes and horn strobes shall have field -selectable <br />candela settings including 15, 30, 75, 95, 110,135, and 185. <br />STROBE <br />The strobe shall be a System Sensor L-Series Model_______ listed to UL 1971 and shall be approved forfire protective service. The <br />strobe shall be wired as a primary -signaling notification appliance and comply with the Americans with Disabilities Act requirements <br />forvisible signaling appliances, flashing at 1 Hz overthe strobe's entire operating voltage range. The strobe light shall consist of a <br />xenon flash tube and associated lens/reflector system. <br />HORN STROBE COMBINATION <br />The horn strobe shall be a System Sensor L-Series Model_______ listed to UL 1971 and UL 464 and shall be approved for fire <br />protective service. The horn strobe shall be wired as a primary -signaling notification appliance and comply with the Americans with <br />Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The <br />strobe light shall consist of a xenon flash tube and associated lens/reflector system. The horn shall have two audibility options and <br />an option to switch between a temporal three pattern and a non -temporal (continuous) pattern. These options are set by a multiple <br />position switch. The horn on horn strobe models shall operate on a coded or non -coded power supply. <br />SYNCHRONIZATION MODULE <br />The module shall be a System Sensor Sync- Circuit model MD L3 listed to UL 464 and shall be approved forfire protective service. <br />The module shall synchronize L-Series strobes at 1 Hz and horns at temporal three. Also, while operating the strobes,the module <br />shall silence the horns on horn strobe models over a single pair of wires. The module shall mountto a 411/16. 411/16. 21/8-inch <br />back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize <br />multiple zones. Daisy chaining two or more synchronization modules together will synchronize allthe zones they control. The module <br />shall not operate on a coded power supply. <br />PHYSICAL <br />Wall -Mount Dimensions (including tens):5.6` L * 4.7` W * 1.25` D <br />(143mmL*119mmW*32mmD) <br />Compact Wall -Mount Dimensions (including lens): 5.26" Lx 3.46" W <br />x1.93" D(133 mm Lx 88 mm Wx 49 mm D) <br />Horn Dimensions: 5.6` L*4.7` W * 1.25" D (143 mm L * 119 mm W <br />32 mm D) <br />Compact Horn Dimensions: 5.25" Lx 3.45" W x 1.25" D (133mm Lx <br />88mm W x32mm D) <br />ELECTRICAL SPECIFICATIONS <br />Strobe Flash Rate: 1 flash per second <br />Nominal Voltage Regulated: 12VDC or regulated 24DC/FWR1 <br />Operating Voltage Range2: 8 to 17.5 V (12 V nominal) or 16 to 33 V (24 <br />V nominal) <br />Operating Voltage Range (MDL3) Sync Module: 8.5 to 17.5V (12 V <br />nominal) or 16.5to 33V (24V nominal) <br />Input Terminal Wire Gauge: 12 to 18 AWG <br />ENVIRONMENTAL <br />Standard Operating Temperature: 320 F to 120°F (0°C to 49°C) <br />Humidity Range: 10 to 93% non -condensing <br />Notes: <br />1. Fu ll W ave Rectified (F W R) voltage is a no n-reg a fated, tl m e-varying <br />power sourcethat Is used on some powersupplyand paneloutputs. <br />2. P, S, PC, and SC products wi lloperate at 12V nominal only for 15 and 30 cd. <br />AGENCY LISTINGS AND APPROVALS <br />UL: Listed <br />FM: Approved <br />CSFM: Listed <br />