10531 29TH AVE SE 2025-06-24 - Laserfiche WebLink

ELECTRCALCHICKLST DETERMINE IF YO LR PRO XCT Q 11ALIFIES FO RELECTRICAL PLAN REVIEW EXEM PTIO N • If you answer yes to all of the below questions, the project qualifies for a Residential Photovoltaic Perm t without full electrical plan review. • If you answer no to any of the below questions, please apply for an Electrical Perm t and subm t full electrical plans for review. Y ES NO 1. PV modules, inverters, and corn Saner boxes are identified for use in PV system s ❑ 2. The inverters are listed and labeled in accordance with UL 1741 and are listed for utility ® ❑ interaction. [IRC M 2302.4] 3. The AC interconnection point is on the load side of service disconnect. [NEC 690.64(B)] ® ❑ 4. The system meets all current NEC, City, and Washington Cities Electrical Code requirements. ❑ 5. For Split-Buss modules the AC interconnection m ust be one of the six service disconnects. ❑ 6. M admum load added to the panel board is based on the rating of the panelboards bus/m an O CPD corn lanation in accordance with NEC 705.12(D)(2)(3)(b), and is lim ted to (check the com tination below that applies): 12225am p bus/200am p m an O CPD-13,400AC watts, m ac 70am p inverter O CPD ❑ 225am p bus/225am p m an O CPD-8,640AC watts, m ac 45am p inverter O CPD. ❑ 200am p bus/200am p m an O CPD-7,860AC watts, m ac 40am p inverter O CPD. ❑ 150am p bus/150am p m an O CPD-5,760AC watts, m ac 30am p inverter O CPD. ❑ 125am p bus/125am p m an O CPD-4,800AC watts, m ac 25am p inverter O CPD. ❑ 125am p bus/100am p m an O CPD-9,600AC watts, m ac 50am p inverter O CPD. ❑ 100am p bus/100am p m an O CPD-3,840AC watts, m ac 20am p inverter O CPD. ❑ O tier Electrical Perm t with Plan Review Required: Note 1: Listed un-altered factory m an/bus com tination. Alteration of the panelboard m an OCPD will require plan review. Note 2: The circuit conductors and overcurrent devices shall be sized to carry not less than 125 percent of the m adm urn currents as calculated in 690.8(A). The rating or setting of overcurrent devices shall be perm tted in accordance with 240.4(B) and (C). [NEC 690.8(B)(1)] Note 3: If a panelboard em ploys a snap switch rated 30 am peres or less in any branch circuit, it cannot be rated m ore than 200 am peres unless there is a supply side overcurrent protection at 200 amperes or less within the panelboard. This requirement does not apply to panelboards equipped with circuit breakers. Section 408.36 a of the NEC. 7. I have attached the following Electrical O re-Line Diagram: ❑ Standard Electrical Diagram - 6 Strings or Less 12 Standard Electrical Diagram -4 Strings or Less ❑ Standard Electrical Diagram - M icro Inverter ❑ None of the above - Electrical Perm it with Plan Review Required AG FEEMENT: I hereby certify that I have read and exam ned this application and know the sam eto be true and correct. All provisions of laws and ordinances governing this type of work will be com pteted whether specified herein or not. The granting of a permit does not presum eto give authority to violate or cancel the provisions of any other state or local law regulating construction or the perform ance of construction. That I am authorized by the owner of this property to perform the work for which application is m ade and I com ply with the State Contractors Law 18.27 RCW and 296.200 WAC . O3200 Cedar Street © 425.257.8810 Perm tServices@ everettwa.gov Everett,WA98201 Sam 12pm,1pm 3pm everettwa.gov/perm is age 2of2