|
FORM U-1 MANUFACTURER'S DATA REPORT FOR PRESSURE VESSELS
<br /> As Required by the Provisions of the ASME Boiler and Pressure Vessel Code Rules,Section VIII,Division 1 Page 1 of 3
<br /> 1.Manufactured and certified by Ace Heaters, LLC, 130 Klug Circle,Corona,California,92878,USA
<br /> (Name and address of Manufacturer)
<br /> 2.Manufactured for HUBBELL WATER HEATERS,45 SEYMOUR STREET,STRATFORD,Connecticut,06615, USA
<br /> Name and address of Purchaser
<br /> 3.Location of installation NOT KNOWN
<br /> (Name and address)
<br /> 4.Type Vertical STORAGE WATER HEATER 75147
<br /> (Horizontal,vertical,or sphere) (Tank,separator,jkt.vessel,heat exch.,etc.) (Manufacturer's serial number)
<br /> NIA 45108 REV.07 75147 2023
<br /> (CRN) (Drawing number) (National Board number) (Year built)
<br /> 5. ASME Code,Section VIII,Div. 1 2021/ N/A N/A N/A
<br /> [Edition and Addenda,if applicable (date)] (Code Case Number) [Special Service per LIG-120(d)]
<br /> Items 6-11 incl. to be completed for single wall vessels,jackets of jacketed vessels,shell of heat exchangers, or chamber of multichamber vessels.
<br /> 6.Shell: (a)Number of course(s) 1 (b)Overall length 5'1.0"
<br /> Course(s) Material Thickness Long.Joint(Cat.A) Circum.Joint(Cat.A,B,&C) Heat Treatment
<br /> No. Diameter Length Spec./Grade or Type Nom. Corr. Type I Full,Spot,None I Eff. jTyLpej Full,Spot,None Eff. Temp. I Time
<br /> 1 36.0"OD T 1.0" SA516-70 0.188" NONE 2 1 NONE 65% 2 1 NONE 1 659/ NIA I NIA
<br /> Bodv Flan es on Shells
<br /> Bolting
<br /> No. Type ID OD Flange
<br /> Min Hub Thk Material Attached Location Num&Size Bolting Washer(OD,ID, Washer
<br /> Material I thk) Material
<br /> NIA NIA NIA NIA NIA NIA NIA NIA NIA NIA NIA I NIA NIA
<br /> 7. Heads:(a) SA516-70 (b) N/A
<br /> (Material spec.number,grade or type)(H.T.-time and temp.) (Material spec.number,grade or type)(H.T.-time and temp.)
<br /> Location(Top, Thickness Radius Elliptical Conical Apex Hemispherical Flat Side to Pressur Category A
<br /> Bottom,Ends) Min. Corr. Crown Knuckle Ratio Angle Radius Diameter Convex IConcavel Type I Full,Spot,None Eff.
<br /> (a) I ENDS I 0.176" I NONE I NIA I NIA I 2:1 I NIA I NIA I NIA I I X I NIA I None I NIA
<br /> (b) I ENDS I 0.176" I NONE I NIA I NIA I 2:1 I NIA I NIA I NIA I I X I NIA I None I NIA
<br /> B dy Flanges on Heads
<br /> Min Hub Bolting
<br /> Location Type ID OD Flange Thk Thk Material How Attached Num&Size EE�El
<br /> Washer(OD,Washer Material
<br /> ID,thk)
<br /> (a) NIA NIA NIA NIA NIA NIA NIA NIA NIA I NIA NIA
<br /> 8.Type of jacket NIA Jacket closure NIA
<br /> (Describe as ogee&weld,bar,etc.)
<br /> If bar,give dimensions;if bolted,describe or sketch NIA
<br /> 9. MAWP 150 psi NIA at max.temp. 390°F NIA Min.design metal temp. 0°F at 150 PSI
<br /> (Internal) (External) (Internal) (External)
<br /> 10. Impact test EXEMPT PER UG 20(f) at test temperature of NIA
<br /> [Indicate yes or no and the component(s)impact tested]
<br /> 11.Hydro.,pneu.,or comb.test pressure Hydro.at 195 PSI Proof test NIA
<br /> Items 12 and 13 to be completed for tube sections.
<br /> 12.Tubesheet SA240-304L 1 SA516-70 8.625" 5/8" NONE BOLTS
<br /> [Stationary(material spec.no.)] [Diameter(subject to press.)] (Nominal thickness) (Corr.allow.) Attachment(welded or bolted)
<br /> NIA NIA NIA NIA NIA
<br /> [Floating(material spec.no.)] (Diameter) (Nominal thickness) (Corr.allow.) (Attachment)
<br /> 13.Tubes SB111 90/10 3/4"X 5/8" 0.040"X 0.065" 12 U
<br /> (Material spec.no.,grade or type) (O.D.) (Nominal thickness) (Number) [Type(Straight or Ll)]
<br />
|