Laserfiche WebLink
0==16 <br />Model W2 (upright, pendent) <br />Model J (New frame with guard installed) <br />Model JD (Legacy frame with guard installed, similar but with zinc finish) ModelW4 <br />(recessed, concealed <br />FinishesO) <br />Table B <br />Standard Finishes <br />Special Application Finishes <br />Sprinkler <br />F1, F2 and FP�ar <br />Escutcheons <br />CCP Cover <br />Plate' <br />Sprinkler <br />F1, F2 and FPar <br />Escutcheons <br />CCP Cover Plate�a <br />Bronze <br />Brass <br />Chrome <br />Elecfroless Nickel PTFF7 <br />Bright Brass <br />Bright Brass <br />Chrome <br />Chrome <br />White Paint <br />Bright Brass(z <br />Satin Chrome <br />Satin Chrome <br />White Polyestedq <br />White Polyester <br />Satin Chrome <br />Custom Color Polyester <br />Custom Color Paint <br />Custom Color Poll <br />Notes: <br />1. Paint or any other coating applied over the factory finish wll l void all approvals and warranties. <br />2. Model FP escutcheons and Model CCP sprinklers utilize a galvanized steel cup with a finished trim ring or cover plate. <br />3. cULus Listed as corrosion resistant. <br />4. FM Approved as corrosion resistant <br />5. For200°F (93°0) maximum temperature rated sprinklers only <br />Installation <br />Model F1 FR Series sprinklers must be installed in accordance with <br />NFPA13 and the requirements of all applicable authorities having <br />jurisdiction. Model FI FR Series sprinklers must be installed with <br />the Reliable sprinkler installation wrench identified in this Bulletin. <br />Any other wrench may damage the sprinkler. The Models W2and <br />W4 wrenches have two sets ofjaws. Use the smallest set of jaws <br />that fit on the wrench flats of the sprinkler. A leak tight sprinkler <br />joint can be obtained with a torque of 8 to 18 Ib-fr (11 to 24 <br />Nm). Do not tighten sprinklers over the maximum recommended <br />installation torque. Exceeding the maximum recommended <br />installation torque may cause leakage or impairment of the <br />sprinkler. <br />Glass bulb sprinklers have orange bulb protectors or protective <br />caps to minimize bulb damage during shipping, handling and <br />installation. Reliable sprinkler installation wrenches are designed <br />to install sprinklers with bulb protectors in place. Remove the bulb <br />protector at the time when the sprinkler system is placed in service <br />for fire protection. Removal ofthe bulb protector before this time <br />may leave the bulb vulnerable to damage. Remove bulb protectors <br />by undoing the clasp by hand. Do not use tools to remove bulb <br />protectors. <br />Maintenance <br />Reliable Model F1 FR series sprinklers should be inspected and <br />the sprinkler system maintained in accordance with N FPA 25, as <br />well as the requirements of any Authorities Having Jurisdiction. <br />Prior to installation, sprinklers should remain in the original <br />cartons and packaging until used. This will minimize the potential <br />for damage to sprinklers that could cause improper operation or <br />non -operation. <br />Do not clean sprinklers with soap and water, ammonia liquid or <br />any other cleaning fluids. Remove dust by gentle vacuuming <br />without touching the sprinkler. <br />Replace any sprinkler which has been painted (other than factory <br />applied). A stock of spare sprinklers should be maintained to <br />allow quick replacement of damaged or operated sprinklers. <br />Failure to properly maintain sprinklers may result in inadvertent <br />operation or non -operation during a fire event. <br />Bulletin 074 Page 8 of 9 <br />January2023 as. rellabiesprinkiercom <br />