Laserfiche WebLink
Mechanical -TO Bolted Branch Outlets <br />STYLES 920 AND 920N <br />Victaulic Mechanical-r Outlet provides a direct branch connection at any location a hole can <br />be cut in pipe. The hole is cut oversize to receive a "holefinder" locating collar which secures <br />the outlet in position permanently. A pressure responsive gasket seals on the pipe O.D. <br />Crosstypeconnections can be achieved by utilizing two upper housings of the same style and <br />size, with the same or differing branch size connections. NOTE. Style 920 and Style 920N <br />housings cannot be mated to each other to achieve a cross connection. <br />Style 920 and Style 920N Mechanical outlets are available with grooved or female threaded <br />outlet. Specify choice on order. Units are supplied painted with plated bolts. Galvanized hous- <br />ings are available, supplied with plated bolts. <br />All sizes of Style 920 and 920N are rated at 500 psi/3450 DEC working pressure on Schedule <br />10 and 40 carbon steel pipe. They may also be used on high density polyethylene or poly- <br />butylene (HDPE) pipe. Pressure ratings on HDPE are dependent on the pipe rating. Contact <br />Victaulic for ratings on other pipe. Style 920 and 920N are not recommended for use on <br />PVC plastic pipe. <br />Standard piping practices dictate that the Mechanical Styles 920 and 920N must be <br />installed so that the main and branch connections are a true 90' angle when permanently <br />attached to the pipeline surface. <br />Additionally, the VicTap110 hole cuttingtool, which allows for hole cutting capabilities on pressurized <br />systems, utilizes the Style 920 Mechanical in conjunction with the Series 726 Vic -Ball Valve to <br />create the Style 931 VicTap11 Mechanical unit. See page 8 for further information. <br />® FM O Vd$ . LPCB • N <br />HNID0 <br />C E CA <br />EN10311 3SEN10311 <br />CPR (EU) CPR (UK) <br />No.3052011 2019 No.465 <br />SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS <br />STYLES 920 AND 920N STYLE 920 CROSS <br />PATENTED <br />MATERIAL SPECIFICATIONS Housing/Coating: Ductile iron conforming to ASTM A-536, grade 65-45-12, with orange enamel <br />coating. Ductile iron conforming to ASTM A-395, grade 65-45-15, is available upon special <br />request. <br />• Optional: Hot dipped galvanized <br />JOB/OWNER <br />System No. <br />Location <br />Gasket: (Specify choice*) <br />• Grade "E" EPDM <br />EPDM (Green color code). Temperature range-30'F to +230oF/-34oC to +110oC. <br />Recommended for cold and hot water service within the specified temperature range plus a <br />variety of dilute acids, oil -free air and many chemical services. UL Classified in accordance <br />with ANSI/NSF 61 for cold +86oF/+30oC and hot+180oF/+82oC. NOT RECOMMENDED FOR <br />PETROLEUM SERVICES. <br />• Grade "T" nitrile <br />Nitrile (Orange color code). Temperature range-20'F to+180oF/-29oC to +82oC. <br />Recommended for petroleum products, air with oil vapors, vegetable and mineral oils within the <br />specified temperature range. Not recommended for hot water services over+150oF/+66oC or <br />for hot dry air over+140oF/+6OoC. <br />*Services listed are General Service Recommendations only. It should be noted that there are <br />services for which these gaskets are not recommended. Reference should always be made to <br />the latest Victaulic Gasket Selection Guide for specific gasket service recommendations and for a <br />listing of services which are not recommended. <br />Bolts/Nuts: Heat -treated plated carbon steel, trackhead meeting the physical and chemical <br />requirements of ASTM A-449 and physical requirements of ASTM A-183. <br />CONTRACTOR <br />Submitted By <br />www.victaulic.com <br />VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY 2022 VICTAULIC COMPANY. ALL RIGHTS RESERVED. <br />REV P <br />ENGINEER <br />Spec Sect <br />Approved <br />Pa ra <br />�Ct9uli0• <br />11.02_1 <br />