3315 SEAWAY BLVD 2025-10-15 - Laserfiche WebLink

TFP220 Page 5of8 Light Hazard Group I Group II Area 0.10 GPM/ft2 Ordinary Hazard Ordinary Hazard Description 0.15 GPM/ft2 0.20 GPM/ftz ft x ft GPM PSI GPM PSI GPM PSI 14 x 14 30 7.2 30 7.2 39 12.1 16 x 16 30 7.2 39 12.1 51 20.7 TY5137 (K=11.2) Upright 18 x 18 33 8.7 49 19.1 65 33.7 20 x 20 40 12.8 60 28.7 80 51.0 14 x 14 30 7.2 30 7.2 39 12.1 16 x 16 30 7.2 39 12.1 51 20.7 TY5237 (K=11.2) Pendent 18 x 18 33 8.7 49 19.1 65 33.7 20 x 20 40 12.8 60 28.7 80 51.0 14 x 14 N/A N/A 39 7.8 51 13.3 16 x 16 N/A N/A 39 7.8 51 13.3 TY6137 (K=14.0) Upright 18 x 18 N/A N/A 49 12.3 65 21.6 20 x 20 N/A N/A 60 18.4 80 32.7 14x14 37 7.0 39 7.8 51 13.3 16 x 16 37 7.0 39 7.8 51 13.3 TY6237 (K=14.0) Pendent 18 x 18 37 7.0 49 12.3 65 21.6 20 x 20 40 8.2 60 18.4 80 32.7 NOTES • 1 ft = 0,3048 m • 1 ft2 = 0,093 m2 • 1 GPM = 3,785 LPM • 1 psi = 0,06895 bar • 1 GPM/ftz= 40,74 mm/min TABLE D FLOW CRITERIA FOR UL AND C-UL LISTING OF SERIES EC-11 AND EC-14 SPRINKLERS Installation TYCO Series EC-11 and EC-14 Extended Coverage Upright and Pendent Sprinklers must be installed in accordance with this section. General Instructions Do not install any bulb -type sprinkler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprin- kler held horizontally, a small air bubble should be present. The diameter of the air bubble is approximately 1/16 in. (1,6 mm) for the 135°F (57°C) to 3/32 in. (2,4 mm) for the 286°F (141°C) tempera- ture ratings. A leak -tight 3/4 in. NPT sprinkler joint should be obtained by applying a min- imum -to -maximum torque of 10 to 20 lb-ft (13,4 to 26,8 N•m). Higher levels of torque may distort the sprinkler inlet with consequent leakage or impairment of the sprinkler. Do not attempt to compensate for insufficient adjustment in an Escutch- eon Plate by under or over -tightening the Sprinkler. Re -adjust the position of the sprinkler fitting to suit. Step 1. Install the sprinkler with the deflector parallel to the mounting surface. Install pendent sprinklers in the pendent position. Install upright sprinklers in the upright position. Step 2. After installing the Style 30, 40, or 60 mounting plate, or other applica- ble escutcheon, over the sprinkler pipe threads and with pipe -thread sealant applied to the pipe threads, hand - tighten the sprinkler into the sprinkler fitting. Step 3. For upright or pendent sprin- klers, wrench -tighten using only the W-Type 3 (End A) Sprinkler Wrench. For the pendent sprinkler installed with Style 30, 40, or 60 Escutcheon, wrench -tighten the sprinkler using only the W-Type 22 Sprinkler Wrench. Apply the wrench recess of the appli- cable sprinkler wrench, as shown in Figure 5 or Figure 6, to the sprinkler wrench flats, as shown in Figure 1.