Laserfiche WebLink
AVAILABILITY <br />Superstud!TM, Superstud!Tm/Nuts! and Molded ISOPLAST® Flanged Hex Nuts are available in diameters <br />of 3/8", 1 /2", 5/8", 3/4" and 1 ". Superstud!TM is stocked in 48" and 96" lengths for immediate delivery. <br />Special lengths and threading can be quoted upon request. Superstud!Tm Nuts! are available in a <br />uniform gray color. <br />PROPERTIES <br />The ultimate thread shear strength, flexural strength, flexural modulus and double shear values were <br />derived via full section testing and are characterized per the requirements of ASTM D7290. The char- <br />acteristic value is based on material property representing the 80% lower confidence bound on the <br />5th percentile value of a specified population. <br />Diameter <br />per Inch <br />Physical/Mechanical Properties <br />Ultimate Thread <br />Type of <br />CPSquare Nut <br />lbs. <br />3/8" <br />811 <br />1/2" <br />1,880 <br />5/81, <br />2,198 <br />3/4" <br />2,692 <br />V, <br />6,616 <br />hear Strength' 23 <br />Flexural Strength 235 <br />D790 <br />psi <br />64,405 <br />68,703 <br />65,170 <br />58,119 <br />54,421 <br />Flexural Modulus 2 <br />D790 <br />106 psi <br />2.4 <br />2.8 <br />2.7 <br />2.8 <br />2.6 <br />Ultimate Double Shear Strength2 3 4 <br />B565 <br />load lb. <br />4,142 <br />7,071 <br />7,186 <br />11,446 <br />22,987 <br />Dielectric Strength <br />D149 <br />kV/in <br />35 <br />35 <br />35 <br />35 <br />35 <br />Water Absorption 24 hr Immersion <br />D570 <br />% <br />1 <br />1 <br />1 <br />1 <br />1 <br />Coefficient of Thermal Expansion (LW) <br />D696 <br />10-6 in/in/°F <br />5.0 <br />5.0 <br />5.0 <br />5.0 <br />5.0 <br />Maximum Recommended Torque <br />trength Using CP Square Nut <br />CP Square Nut <br />ft-lbs <br />4 <br />8 <br />16 <br />24 <br />50 <br />Lubricated with SAE 1 OW30 Motor Oil' <br />tud Weight <br />Ib/ft <br />0.076 <br />0.129 <br />0.209 <br />0.315 <br />0.592 <br />e- <br />Flammability <br />CP Square Nut <br />D635 <br />Extinguishing <br />on All <br />Thickness Nut <br />CP Square Nut <br />in <br />0.437 0.562 0.688 0.813 1.062 <br />0.750 1.75 <br />Width Nut <br />CP Square Nut <br />in <br />0.688 0.875 1.062 1.250 1.625 <br />2.000 <br />Applies to singe nut on y. <br />2 Values statistically derived per ASTM D7290 on the actual studs. <br />3 Appropriate safety factors shall be applied. <br />4 Single Shear can be estimated by dividing the double shear value in half. <br />5 Flexural strength governed by compression failure. Therefore, flexural and compression strength are the same in bending. <br />Note: Superstud!TM is intended to be used only with the CP Molded and Square Nuts. Steel Nuts are Excluded. <br />Creative Pultrusionst, Flowgript, Pultext, Supergratet, SUPERPILEt, Superplankt, SuperLoct, SuperWalet , Superdeckt, and STORMSTRONOt <br />are registered trademarks of Creative Pultrusions, Inc. <br />Superstud!TM, Superstudl— Nuts!, SUPURTUF-, Tut-dek—, SuperCap— and SuperRod- are trademarks of Creative Pulmisions, Inc. <br />�p <br />CREATIVE <br />PULTRUSIONS <br />214 Industrial Lane, Alum Bank, PA 15521 <br />839.4186 • Fax 814.839.4276 • Toll Free 888.CPI.PULL 30 <br />www.creativepultrusions.com CPM071-0212.1 c <br />DLR: 09.03.15 <br />