|
2
<br />3
<br />2
<br />5
<br />6
<br />7 I g I g I I I 10 I 11
<br />9
<br />F
<br />E
<br />� D
<br />Ci
<br />0
<br />N
<br />0
<br />0
<br />rn
<br />r-
<br />L
<br />0
<br />0
<br />0
<br />0►
<br />0
<br />O
<br />0
<br />0
<br />U)
<br />w
<br />0I
<br />N
<br />0
<br />Q
<br />UI
<br />ti
<br />CO
<br />w
<br />w C
<br />cn
<br />J
<br />J
<br />L
<br />w
<br />2
<br />0-
<br />0
<br />w
<br />w
<br />0
<br />Q� .
<br />J
<br />J
<br />2
<br />w
<br />w
<br />w
<br />¢I
<br />T-
<br />0
<br />4
<br />rn
<br />ti
<br />Un
<br />,
<br />6
<br />N
<br />J
<br />Q
<br />0- B
<br />U
<br />Q
<br />X
<br />In
<br />ZD
<br />U
<br />X
<br />J
<br />E:
<br />a-
<br />'t
<br />r
<br />N
<br />. N
<br />N
<br />O
<br />N -
<br />00
<br />i6i
<br />2
<br />w
<br />Q
<br />0
<br />X
<br />Q A
<br />z
<br />w
<br />V
<br />co
<br />C
<br />w
<br />E-
<br />i-
<br />0
<br />J
<br />0-
<br />ACCESSIBILITY NOTES:
<br />THIS LIST IS NOT ALL INCLUSIVE. FOR CONDITIONS NOT COVERED, CONTACT THE ARCHITECT.
<br />A. At least one accessible route shall be provided within the site from accessible parking spaces and
<br />accessible passenter loading zones; public streets and sidewalks; and public transportation stops to
<br />the accessible building or facility entrance they serve.
<br />A. Carpet or carpet tiles provided on a floor surface shall be securely attached; be firm, have a level
<br />loop, textured loop, level cut pile, or level cut/uncut pile texture. Maximum pile height shall be 1/2". Exposed
<br />edges of carpet shall be fastened to floor surfaces and have trim along the exposed edges.
<br />11B-302.3 - OPENINGS
<br />A. Openings in floor or ground surfaces shall now allow passage of a sphere more than 1/2" diameter.
<br />B. Elongated opening shall be placed so that the long dimension is perpendicular of the dominant direction of travel.
<br />11B-303 - CHANGES IN LEVEL
<br />11 B-303.2 - VERTICAL (REFERENCE FIGURE 11 B-303.2 as shown on this sheet)
<br />A. Changes in level up to 1/4" maximum may be vertical and without edge treatment.
<br />11B-303.3 -BEVELED (REFERENCE FIGURE 11B-303.3 as shown on this sheet)
<br />B. Changes in level between 1/4" high minimum and 1/2" maximum shall be beveled with a slope no greater than 1:2 (50%).
<br />2
<br />11
<br />-_ r
<br />-
<br />r N
<br />2
<br />�� I r � -J �
<br />FIGURE 11B-303.2 FIGURE 11_B-303.3
<br />VERTICAL CHANGE IN LEVEL BEVELED CHANGE IN LEVEL
<br />116-304 -TURNING SPACE
<br />A. The space required to make a wheelchair turn to make a 180' turn is 60" diameter to a "T-shaped" space.
<br />11B-305 - CLEAR FLOOR GROUND SPACE
<br />A. Minimum clear floor space for a wheelchair and occupant shall be 30" wide x 48" long. Clear floor space
<br />may be positioned for forward or parallel approach. Clear floor space shall be centered on the element it serves.
<br />B. One full unobstructed side of the clear floor space adjoins or overlaps an accessible route or adjoins
<br />another wheelchair clear floor surface.
<br />11 B-307 PROTRUDING OBJECTS
<br />11 B-307.1 - GENERAL
<br />A. Objects projecting from walls (for example, telephones) with their leading edges between 27" - 80" above
<br />the finished floor shall protrude no more than 4" maximum horizontally into the circulation path.
<br />B. Free-standing objects mounted on posts or pylons may overhang 12" maximum when located 27" minimum
<br />and 80" maximum above the ground or finished floor.
<br />4 ---7--;�4" MAX NO MIN.
<br />LOBBY ,k--- NO MAX.
<br />z
<br />ti
<br />N
<br />11 B-307.4 - VERTICAL CLEARANCE
<br />A. Vertical clearance shall be 80" high minimum room.
<br />DIVISION 4 ACCESSIBLE ROUTES
<br />11 B-403 WALKING SURFACES
<br />11 B-403.5 - CLEARANCES
<br />A. The minimum clear width for single wheelchair passage shall be 32" at a point and 36" continuously.
<br />11B-403.5.1 - CLEAR WIDTH
<br />A. Walkways maintain a minimum 48" width.
<br />B. Walkways less than 60" wide shall have a minimum 60" x 60" landing not to exceed every 200 ft.
<br />11B-403.5.3 - PASSING SPACE
<br />A. The minimum clear width for two wheelchairs to pass is 60".
<br />11 B-403.3 - SURFACE CROSS SLOPES
<br />A. Cross slope shall not exceet 1:48.
<br />11 B-403.3 - SLOPE
<br />A. Running slope shall not exceet 1:20 (5%). (If slope exceets 1:20 (5%), refer to section 11 B-405 RAMPS).
<br />DIVISION 5 - GENERAL SITE AND BUILDING ELEMENTS
<br />116-502 - VEHICLE SPACES
<br />A. Car and van spaces shall be 18'-0" long minimum. Car parking spaces shall be 9'-0" wide minimum and
<br />van parking spaces shall be 12'-0" wide minimum, shall be marked to define the width and shall have an
<br />adjacent aisle complying with Section 11 B-502.3.
<br />Exception: Van parking spaces shall be permitted to be 9'-0" wide minimum where the access aisle is 96"
<br />wide minimum.
<br />B. Parking access aisles shall be 5'-0" wide minimum and extend the length of the parking stall they serve.
<br />Access aisles must adjoin an accessible route.
<br />C. Surface slope shall not exceet 1:48 in all directions.
<br />D. Provide minimum vertical clearance of 98" at accessible parking spaces, access aisles and along
<br />at least one vehicle access route to such spaces from site entrances and exits.
<br />11B-502.6 - MARKING OF PARKING SPACES
<br />A. Each accessible parking space must have an individual vertically mounted sign. Required van accessible
<br />spaces must be designated and
<br />shall have an additional sign or additional language stating "Van Accessible".
<br />B. Characters and symbols on such signs shall be located 80" minimum above the ground, or 36" if wall mounted.
<br />11 B-405 - RAMPS
<br />11 B-406 - SLOPE OF CURB RAMPS (REFERENCE FIGURE 11 B-406.2.2 & 406.3.2 as shown on this sheet)
<br />A. Slopes of curb ramps shall not exceet 1:12 gradient (8.33%).
<br />Note: Maximum cross slope of 1:48 at all ramps and level surface areas.
<br />B. Maximum slopes of adjoining gutters, road surface immediately adjacent to the curb ramp, or accessible
<br />route shall not exceet 1:20 (5%).
<br />1126.5, PART 2 - WIDTH OF CURB RAMPS (REFERENCE FIGURE 11 B-406.2.2 & 11 B-406.3.2 as shown on this sheet)
<br />A. The minimum width of a curb ramp shall be 487, exclusive of flared sides.
<br />11276.5, PART 3 - SIDES OF CURB RAMPS (REFERENCE FIGURE 11 B-406.2.2 & 11 B-406.3.2 as shown on this sheet)
<br />A. If a curb ramp is located where pedestrians must walk across the ramp or where it is not protected by
<br />handrails or guardrails, it shall have flared sides; the maximum slope of the flare shall be 1:10 (10%).
<br />� Q&„
<br />Adjoining Slope Shall
<br />1%
<br />/ Not Exceed 1:20
<br />landing to be
<br />at least as
<br />Flared sides 1:10 max slope.
<br />wide as curb
<br />ramp
<br />4V' Min.
<br />-
<br />r- I ;,;,'
<br />'--
<br />slope
<br />, r -_, ,r" k. -%, i
<br />',1 - J, , , n ♦ ,
<br />S- ' ,'fi
<br />, J
<br />t
<br />- R, 7/
<br />slope ; - _ .-
<br />Ramp (1:12 Max. Slope) shall have
<br />.
<br />detectable warnings with
<br />11 i �-
<br />contrasting color, see Fig. 11 B-406
<br />CBC and Fig 11 B-705.1 as shown
<br />on this sheet
<br />FIGURE 11 B-406.2.2
<br />STANDARD RAMP
<br />-------,
<br />Detectable Warning with
<br />contrasting color, see Fig.
<br />11 B-406 CBC and Fig. 11 b-705.1
<br />as shown on this sheet---
<br />/ i" ... ... ... �
<br />Adjoining Slope Shall
<br />Not Exceet 1:20
<br />-_,t
<br />- �Cl, -i , ' a -- $ c- -
<br />:5�, , .I- , - . .- _ -
<br />'i 9
<br />48" Mire --
<br />FIGURE 11 B-406.3.2
<br />PARALLEL TO CURB
<br />48" Min.
<br />Location of Typical Parking
<br />Access Aisle
<br />Ramps (1:12 Max. Slope)
<br />a-
<br />LO
<br />M
<br />CV
<br />A
<br />15" at top
<br />.9" at base
<br />TYPICAL PLAN
<br />FIGURE 11 B-705.1
<br />TRUNCATED DOMES
<br />0.2" HT.
<br />1
<br />- ---- Tapered edges
<br />where exposed
<br />TYPICAL SECTION A -A
<br />11 B-503 - PASSENGER LOADING ZONES
<br />11 B-503.5 - GENERAL + VERTICAL CLEARANCES
<br />A. Passenger loading zones shall provide an access aisle at least 60" wide minimum and 20 ft long minimum
<br />adjacent and parallel to the vehicle pull-up space. Vehicle standing spaces and access aisles shall be at the same
<br />level as the vehicle pull-up space they serve. Changes in level are not permitted. Exception: slopes not sleeper than
<br />1:48 shall permitted.
<br />B. Provide minimum vertical clearance of 114" at accessible passenger loading zones and along at least one
<br />vehicle access route from site entrances and exits. .
<br />11B-406.5.9 - DIAGONAL CURB RAMPS
<br />A. If diagonal curb ramps have returned curbs or other well-defined edges, such edges scall be parallel to the
<br />direction of pedestrian flow. The bottom of diagonal curb ramps shall have 48" minimum clear space. If diagonal
<br />curb
<br />ramps are provided at marked crossings, the 48" clear space shall be within the markings. If diagonal curb ramps
<br />have flared sides, they shall also have at least a 24" long segment of straight curb located on each side of the
<br />curb ramp and within the marked crossing.
<br />11 B-406.6 ISLANDS
<br />A. Any raised islands in crossings shall be cut through level with the street or curb ramps at both sides. The
<br />clear width of the accessible route at islands shall be 60" wide minimum.
<br />11 B-406 - CURB RAMPS, BLENDED TRANSITIONS AND ISLANDS
<br />11 B-406.1 - GENERAL
<br />A. Curb ramps, blended transitions and islands on accessible routes shall comply with Section 11 B-406.
<br />11B-406.5.2 - CURB RAMP WIDTH
<br />A. The minimum clear width of a ramp shall be 48".
<br />Note: Maximum cross slope of 1:48 at all ramps and level surface areas.)
<br />11 B-406.3.1 - CURB RAMP SLOPE
<br />A. The running slope of the curb ramp segments shall be in -line with the direction of the sidewalk travel. Ramp
<br />runs shall have a running slope not steeper than 1:12.
<br />11B-406.5.3 - CURB RAMP LANDINGS
<br />A. Level landings required at top of each ramp. The slope of the landing in all directions shall be 1:48 maximum.
<br />(REFERENCE FIGURE 11B-406.2.2 & 11B-406.3.2 as shown on this sheet)
<br />11 B-405 - RAMPS
<br />11B-405.1 - GENERAL
<br />A. Ramps on accessible routes shall comply with section 11 B-405.
<br />1 1 B-405.7.2.1 - SIZE TOP LANDING
<br />A. Top landings shall not be less than 60" wide and shall have a length of 60" in the direction of ramp run.
<br />11 B-405.7.3.1 - SIZE BOTTOM LANDING
<br />A. Landings at the bottomof ramps shall extend 72" minimum in the direction of the ramp run.
<br />11 B-405.7.2 - WIDTH OF LANDING
<br />A. At the bottom and Intermediate landings the width shall be the same as required for ramps.
<br />11B-405.7.4 - CHANGE OF DIRECTION
<br />A. Ramps that change direction between runs at landing shall have a clear landing 60" minimum by 72" minimum
<br />in the direction of downward travel from the upper ramp run.
<br />11 B-405.8 - HANDRAILS FOR RAMPS
<br />A. Handrails are required at all ramps with more than a 6" rise.
<br />B. Height: 34" minimum - 38" maximum above ramp surface.
<br />C. The clear space between the handrail and the wall shall be 1-1/2" minimum.
<br />D. Handrails shall be at each side of ramp.
<br />E. Handrails shall extend 12" of level distance beyond top and bottom of ramp and parallel to the floor or ground
<br />surface. The inside handrail on switchback ramps shall always be continuous.
<br />11B-406.9 - EDGE PROTECTION
<br />A. Edge protectino complying with Section 11 B-405.9.2 shall be provided on each side of ramp runs and at each
<br />side of ramp landings.
<br />11 B-303.5 - WARNING CURBS
<br />A. Warning curbs shall be at least 6" in height above the walk or sidewalk surface.
<br />B. Warning curbs are not required when a guard or handrail is provided with a guiderail centered 2" minimum
<br />and 4" maximum above the surface of the walk or sidewalk.
<br />11 B-404 DOORS, DOORWAYS AND GATES
<br />11B-404.2.2 DOUBLE -LEAF DOORS AND GATES
<br />A. At least one of the active leaves of doorways with two leaves shall comply with sections 11 B-404.2.3 and
<br />11 B-404.2.4
<br />11 B-404.2.3 - CLEAR WIDTH
<br />A. Door openings shall provide a clear width of 32" minimum, with the door open 90°.
<br />1. Clear openings shall be measured between the face of the door.and opposite stop.
<br />2. Openings more than 24" in depth shall provide a clear opening of 36" minimum.
<br />Exception: Doors not requiring full user passage, such as shallow closets, may have a clear opening of 20"
<br />minimum.
<br />11 B-404.2.4 - MANEUVERING CLEARANCES AT DOORS
<br />Provide level (1:50 (5%) max. slope) and clear maneuvering area at doors as follows:
<br />A. Front approach pull side - 60" minimum length & 18" minimum beside strike edge 24" at exterior doors.
<br />B. Front approach push side - 48" minimum length & 0" beside strike edge (12" at strike if door has both a closer
<br />and a latch.)
<br />. C. Hinge side approach pull side - 60" minimum width; 36" minimum beside strike edge.
<br />D. Hinge side approach push side - 44" minimum width & 22" minimum beside hinge edge (48" minimum width if
<br />door has both a closer and a latch.) .
<br />E. Latch side appraoch pull side - 60" minimum width and 24" minimum beside strike edge (54" minimum width if
<br />door has a closer).
<br />F. Latch side approach push side - 44" minimum width and 24" minimum beside strike.edge (48" minimum width if
<br />door has a closer).
<br />11 B-404.2.5 - THRESHOLDS AT DOORWAYS
<br />A. The height of the threshold shall be at a maximum of 1/2" above the floor/landing.
<br />B. Change in level between 1/4" and 1/2" shall be beveled with a slope no greater than 1:2 (50%) slope.
<br />Note: The threshold shall have vertical edges no greater than 1/4".
<br />11B-404.2.9 - DOOR OPENING FORCE
<br />A. The maximum force for pushing or pulling open a door shall be as follows:
<br />1. Fire doors shall have the minimum opening force allowable by the appropriate administrative authority, not
<br />to exceed 15 Ibf.
<br />2. Other doors:
<br />. I a. Exterior hinged doors: 5 Ibs maximum
<br />b. Interior hinged doors: 5 Ibs maximum
<br />c. Sliding or folding doors,: 5 Ibs maximum
<br />11 B-404.2.8.1 - DOOR CLOSERS
<br />A. If a door has a closer, then the sweep period of the closer shall be adjusted so that from an open po
<br />sition of
<br />900, the time required to move the door to a position of 120 from the latch is 5 seconds.
<br />11 B-404.2.7 - DOOR HARDWARS
<br />A. Handles, pulls, latches, locks, and other operating devices shall have a shape that is easy to grasp. with one
<br />hand and does not require tight grasping, tich pinching, or twisting of the wrist to operate.
<br />B. Hardware required for accessible door passage shall be centered between 34" minimum and 44" maximum
<br />above finish floor.
<br />C. Lever -operated mechanisms and push-pull activating -type mechanisms are acceptable designs.
<br />11 B-404.2.10 - DOOR SURFACE
<br />A. Swinging door and gate surfaces within 10" of the finish floor or ground measured vertically shall have a smooth
<br />surface on the push side extending the full width of the door or gate.
<br />11 B-602 - DRINKING FOUNTAINS
<br />11B-602.4 - SPOUT HEIGHT (REFERENCE FIGURE 11B-313 as shown on this sheet)
<br />A. Accessible spouts shall be no higher than 36" , measured from the floor or ground surface to the spout outlet.
<br />B. In addition to the accessible drinking unit, at least one drinking fountain shall be at a standard height (38"
<br />minimum and 43" maximum above finish floor). A "hi -low" fountain will accommodate both requirements.
<br />11 B-602.2 - CLEARANCES + ALCOVES (REFERENCE FIGURE 11 B-36 as shown on this sheet)
<br />A. Wall and post -mounted cantilever fountains shall have clear knee space as follows:
<br />1. Minimum 27" high (from apron bottom to floor) minimum 30" wide, and 18"-19" deep.
<br />2. A clear floor space allowing a forward approach to the unit shall be provided. The minimum clear floor space
<br />shall be 30" wide x 48" deep.
<br />11 B-602.9 - PEDESTRIAN PROTECTION
<br />A. Drinking fountains shall be located within alcoves, wing walls or otherwise positioned not to encroach into
<br />pedestrian ways. The minimum alcove size shall be 32" wide minimum x 18" deep minimum.
<br />11B-211.2 -ACCESSIBLE DRINKING FOUNTAIN REQUIREMENTS
<br />A. Where only one drinking fountain area is provided on a floor, there shall be a drinking fountain that is accessible to
<br />individuals who use wheelchairs and one that is accessible to those who have difficulty bending or stooping. This can
<br />be accommodated by use of "hi -low" fountains.
<br />B. Where more than one drinking fountain is provided on a floor, 50% of those provided must be wheelchair
<br />accessible. .
<br />DRINKING FOUNTAIN HEIGHTS AND CLEARANCES: E.Q. E.Q.
<br />11 8" TO9" EQUIPMENT 48"MIN.
<br />PERMITTED IN 6" MAX.
<br />SHADED AREA
<br />z o% C � ; o
<br />,
<br />J , J J '
<br />X U �; U U +�
<br />Z <t r
<br />';,� Z L, ; Z Z t-
<br />_� � i
<br />f-- GU -
<br />EL 1,
<br />�,7 �--
<br />---- NCV co 11 -
<br />co 14�- "I
<br />- co M ,-,
<br />-F-17
<br />' 4jr I:,
<br />- 1�- 7- l _ _
<br />Y '
<br />11 11
<br />i , /
<br />48" MIN. 11* I
<br />'� , �_-
<br />8" MIN. 8
<br />KNEE CLR. � � MAX. _ 18" MIN. Q
<br />TOE CLR. 9
<br />17" MIN.. ~
<br />DEPTH � 0 .
<br />FREE STANDING RECESSED = = HI -LOW
<br />SIDE ELEVATION (IN PLAN) (IN PLAN) m 0 (IN ELEVATION)
<br />FIGURE 11 B-3B
<br />11 B-604 - WATER CLOSETS AND TOILET COMPARTMENTS
<br />118-604A - HEIGHT OF WATER CLOSET (REFERENCE FIGURE 100 as shown on this sheet)
<br />NOTE:
<br />At alcoves deeper than 24" additional 6" maneuvering clearance is required. At "hi -low" type fountains, center the 30" x 48" clear floor space on the
<br />"LOW" fountain fixture.
<br />A. The height to the top of the toilet seat shall be 17" minimum -19" maximum from the finished floor.
<br />Note: The dimension is measured from the floor to the top of a 2" maximum high toilet seat.
<br />B. Seats shall not be sprung to return to a lifted position.
<br />11 B-604.5 - GRAB BARS (REFERENCE FIGURE 100 as shown on this sheet)
<br />A. For water closets not located in toilet stalls, the following grab bars shall be provided:
<br />1. Side wall: minimum 42" long, 12" minimum from back wall.
<br />2. Rear wall: minimum 36" long, measured from the center line of water closet to 12" minimum at one end of
<br />grab bar and 24" minimum on the other end of the grab bar.
<br />Note: The grab bars are measured 33" minimum and 36" maximum above finish floor measured to the top of of the griping surface.
<br />11B-604.4 - FLUSH CONTROLS (REFERENCE FIGURE 100 as shown on this sheet)
<br />A. Controls shall be 44" maximum above the finish floor.
<br />B. Lever controls or flush valves shall be mounted on the wide side of toilet areas.
<br />C. The force required to activate controls shall be no greater than 5 Ibf.
<br />D. Controls shall be operable with one hand and shall not require tight grasping, pinching, or twisting of the wrist.
<br />Note: Controls shall be hand operated or automatic.
<br />11 B-604.7- TOILET TISSUE DISPENSERS (REFERENCE FIGURE 100 as shown on this sheet)
<br />A. Toilet paper dispensers shall be installed on the side wall, a minimum 19" above the floor to centerline of dispenser.
<br />Note: Dispensers that control delivery or do not permit continuous paper flow shall not be used.
<br />B. Centerline of dispenser shall be 7" minimum and 9" maximum from the front of the toilet
<br />1 1 B-604.8.2.2 - DOORS AT WATER CLOSET COMPARTMENT(S)
<br />A. Toilet stall doors shall have an automatic -closing device and shall have clear, unobstructed opening width of 32" when located
<br />at the end and 34" when located at the side with the door located at 900 from its closed position.
<br />11B-604.9.1 - SIZE AND ARRANGEMENT AT TOILET STALLS (REFERENCE FIGURE 100 as shown on this sheet)
<br />A. Toilet stalls may be arranged to provide either a left or a right handed approach.
<br />SINGLE ACCOMODATION TOILET FACILITY: ACCESSIBLE WATER CLOSET COMPARTMENT
<br />FLUSH
<br />ACTIVATOR
<br />2 17" TO 18" ON WIDE 18" MIN. ,
<br />CN SIDE
<br />0
<br />Z-�- - ] , -- - ,,\
<br />I T
<br />7T, \
<br />t
<br />L0 -
<br />,
<br />a ' ,
<br />2-7
<br />z
<br />Cy 11 ME t
<br />--,� J 1J - -J1 %\ _ !
<br />so
<br />a ,`
<br />32" MIN. CLR.
<br />18" MIN. CLR.
<br />WITHIN A MULTIPLE -ACCOMMODATION TOILET
<br />FACILITY:
<br />�
<br />17" TO 18" FLUSH
<br />ACTIVATOR ON
<br />CN
<br />I 1 1 WIDE SIDE
<br />2i ZI `�
<br />J
<br />Z U
<br />1E z
<br />:57-
<br />N =.
<br />M
<br />1- i � . � . =T �
<br />32" MIN. CLR.
<br />�I \ 4" MAX.
<br />18" MIN. CLR, ,X
<br />,�
<br />it
<br />�
<br />.
<br />TOILET FACILITY MOUNTING AND INSTALLMENT HEIGHTS
<br />W
<br />o J
<br />,m
<br />54" MIN.
<br />w U
<br />6" HOLD
<br />12" MAX.
<br />z 0
<br />36" MIN. - ��-i
<br />42" MIN. GRAB BAR
<br />w
<br />GRAB BAR
<br />a=
<br />0
<br />=
<br />24" MIN. 12" MIN.
<br />o�--
<br />-p- rELONGATED
<br />RIM
<br />AR
<br />irf�clo
<br />11 24" MIN.
<br />TRANSFER SIDE
<br />-a'0
<br />�_ .
<br />TOP OF SEAT
<br />2 �
<br />.
<br />MAX. HIGH SEAT
<br />T2"
<br />71
<br />o)
<br />�
<br />. -----K--�*-\
<br />LL��-
<br />co -N
<br />M -Jl\
<br />�
<br />�
<br />I
<br />I 11
<br />I 1
<br />18" HOLD
<br />7" MIN. 19" MAX.
<br />M
<br />M
<br />/
<br />.
<br />CE
<br />�
<br />I
<br />I I .
<br />NOTE: R ¢
<br />FIGURE 100 SHOWS MINIMUM REQUIREMENTS. SEE DEtLkV1 ON SHEET A307 FOR ENLARGED FLOOR
<br />PLAN OF EXISTING PUBLIC RESTROOM CONDITIONS. Z 0
<br />-0
<br />= r-
<br />11B-213.2 - MULTIPLE -ACCOMMODATION TOILET FACILTIES
<br />A. If toilet stalls are provided in a toilet room or bathroom, then at least one stall shall be a "standard" accessible toilet stall
<br />(for wheelchair users) complying with this Section 11 B-603.
<br />B. Provide at least one ambulatory accessible compartment where six or more compartments are provided within
<br />a multiple -accommodation toilet room. (This is in addition to the accessible water closet.) The provided compartment
<br />shall be 36" wide with an outward swinging self -closing door and parallel grab bars complying with Section 11 B-604.5.
<br />11B-605.2 -HEIGHT OF ACCESSIBLE URINALS (REFERENCE FIGURE 101 as shown on this sheet)
<br />A. Urinals shall be stall -type or wall hung with a tapered, elongated rim at 17" maximum above the finished floor. The rim shall
<br />extend a minimum of 131/2" from the wall.
<br />11B-605.3 -CLEAR FLOOR SPACE + APPROACH (REFERENCE FIGURE 101 as shown on this sheet)
<br />A. A clear floor space 30" wide x 48" deep minimum shall be provided in front of urinal to allow forward approach.
<br />1. This space shall adjoin or overlap an accessible route.
<br />2. Urinals installed in alcoves deeper than 24" require a maneuvering area of at least 36" minimum wide, centered on fixture.
<br />11B-605.4 FLUSH CONTROLS (REFERENCE FIGURE 101 as shown on this sheet)
<br />A. Controls shall be 44" maximum above the finished floor.
<br />1. Controls shall be hand operated or automatic.
<br />2. Controls shall be operable with one hand and shall not require tight grasping, pinching, or twisting of the wrist.
<br />3. The force required to activate controls shall be no greater than 5 Ibf.
<br />15„ P --- -
<br />IT-
<br />,_ r , a
<br />`i_
<br />,..:_ - _ „
<br />48" MIN. ' T -'
<br />I/ '. ,
<br />I
<br />_ F v
<br />=�
<br />,; ;�
<br />-,' ; = 3
<br />. \\\\\ ',! ,,1 t,a
<br />- ` „i
<br />z CLEAR --
<br />. - \
<br />w
<br />0 a- = FLOOR . ,, ; -%-
<br />,;
<br />U w o r ' `";
<br />Q w "' SPACE 2-, =t \\\N _ ` - -`
<br />11 \9'�
<br />¢ i _
<br />¢ i
<br />z W 13.5" MIN.
<br />= 0 PLAN VIEW /I /I ELEVATION
<br />co
<br />M
<br />11 B-606 - LAVATORY HEIGHT + CLEARANCES (REFERENCE FIGURE 11 B-600 as shown on this sheet)
<br />A. Lavatories shall be mounted with the rim or counter surface no higher than 34" above the finished floor.
<br />1. Lavatories shall extend 17" minimum from the wall.
<br />2. Clearance of 29" minimum shall be provided from the finished floor to bottom of the apron.
<br />3. Knee clearance of 27" minimum shall extend 8" minimum under the front of the lavatory.
<br />4. Toe clearance of 9" minimum shall be provided for the full depth of the lavatory.
<br />17" MAX.
<br />00!�
<br />0
<br />�,- Z �
<br />Z 2 2E � CLEAR [ /
<br />z ® 0 I O
<br />FLOOR
<br />o Z� 2 2 2 CD
<br />SPACE
<br />2. N �'' ,T m 19" MAX.
<br />M0
<br />~ I r/
<br />8" MIN, 6" MAX. 48" MIN. LA
<br />17" MIN. ' SIDE ELEVATION PLAN VIEW
<br />,I 'I
<br />FIGURE 11 B-600
<br />LAVATORY+ MIRROR MOUNTING HEIGHTS AND CLEARANCES
<br />11 B-606.4 - FAUCETS
<br />A. Controls shall be operable with one hand and shall not require tight grasping, pinching, or twisting of the wrist.
<br />B. The force required to activate controls shall be no greater than 5 Ibf.
<br />C. Acceptable faucet designs include: lever -operated, push -type, and electronically controlled mechanisms.
<br />D. If self -closing valves are used, the faucet shall remain open for at least 10 seconds.
<br />11B-606.5 - EXPOSED PIPES + SURFACES BENEATH LAVATORIES
<br />A. Hot water and drain pipes under lavatories shall be insulated or otherwise configured to protect against contact.
<br />B. There shall be no sharp or abrasive surfaces under lavatories.
<br />11 B-603.3 - MIRRORS (REFERENCE FIGURE 11 B-600 as shown on this sheet)
<br />A. Mirrors shall be mounted with the bottom edge of the reflecting surface 40" maximum above the finished floor.
<br />11B-609.2.1 - GRAB BARS / 11B-609.3 - DIAMETER SIZE + SPACING
<br />A. Grab bars with a Circular cross section to have a diameter or width of gripping surface shall be 1-1/4" to 2" maximum.
<br />B. The space between grab bars and adjacent walls shall be 1-1/2" minimum.
<br />11 B-609.8 - GRAB BARS - STRUCTURAL STRENGTH
<br />A. Grab bars and mounting devices shall meet the following requirements:
<br />1. Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250
<br />pounds is applied at any point on the grab bar, faster, mounting device, or supposering structure.
<br />11 B-609.5 GRAB BARS - SURFACE
<br />A. Grab bars and adjacent wall surfaces shall be free of sharp or abrasive surfaces and shall have rounded edges.
<br />11 B-603.5 - ACCESSORIES
<br />GENERAL: Where towel, sanitary napkins, waste receptacles, dispensers, other equipment and controls are provided
<br />at least one of each type shall be located on an accessible route, with all operable parts, including coin slots, within 40"
<br />from the finished floor.
<br />11 B-602.5 - SPOUT LOCATION
<br />A. Spouts shall be located at the front of the unit (15" minimum from the vertical support and 5" maximum from the
<br />front edge including bumpers and the water stream from the bubbler shall have a flow in a trajectory that is parallel
<br />(or nearly parallel) to the front edge of the unit.
<br />1. The spout shall provide a flow of water at least 4" high minimum .
<br />2. If the fountain has a round or oval bowl, the spout must be positioned so the flow of water is within 3" of the
<br />front edge of the fountain.
<br />11 B-602.3 - OPERABLE PARTS
<br />A. The flow of water shall be activated by a manually operated system that is front mounted or side mounted and
<br />located within 6" of the front edge of the fountain or an automatic electronically controlled device. Maximum
<br />force to operate is 5 Ibf.
<br />DIVISION 7 - COMMUNICATION ELEMENTS AND FEATURES
<br />11B-703 -SIGNS
<br />11B-703.1 - GENERAL
<br />A. When new or additional signs and/or identification devices are provided or when existing signs are
<br />replaced/altered, the new/altered signs shall comply with 11 B-703: types include:
<br />1. Identification signs
<br />2. Directional & informational signs
<br />3. Accessibility signs
<br />11 B-703.7.1 / 11 B-703.6.2 - FINISH AND CONTRAST
<br />A. Characters, symbols and background of signs shall have a non -glare finish.
<br />B. Characters and symbols shall contrast with their background (i.e. a light characters on a dark background or
<br />dark characters on a light background).
<br />11B-703.2.4 - PROPORTIONS
<br />A. Visual characters on signs shall be selected from fonts where the width of the uppercase letter "O" is 60
<br />percent minimum and 110 percent maximum of the uppercase letter "I". Stroke thickness of the uppercase letter "I"
<br />shall be 10 percent minimum and 20 percent maximum of the height of the character.
<br />11 B-703.5.5 - CHARACTER HEIGHT
<br />A. Characters on signs shall be appropriately sized according to the viewing distance from which they are to be
<br />read, refer to the "Visual Character Height" table in section 11 B-703.5.5
<br />B. Pictorial symbol signs (pictograms) shall be accompanied by the verbal (i.e. text) description placed directly
<br />below the pictogram. The outside dimension of this pictogram shall be a minimum of 6 inches in height.
<br />C. Characters and Braille shall be in a horizontal format.
<br />D. Braille shall be placed at a minimum of 3/8" and a maximum of 1/2" directly below the tactile characters, flush
<br />left or centered.
<br />E. When tactile text is multilined, all Braille shall be placed together below all lines of tactile text.
<br />11 B-703.3 - BRAILLE (REFERENCE FIGURE 3 as shown on this sheet)
<br />A. Braille dots are 1/10" on center in each cell with 2/10" space between cells, measured from the second column
<br />of dots in the first cell to the first column of dots in the Second cell.
<br />B. Braille dots are raised a minimum of 1/40" above the background.
<br />C. Braille dots are domed or rounded.
<br />11B-703.3.2 - MOUNTING LOCATION & HEIGHTS (REFERENCE FIGURE 2 as shown on this sheet for restrooms)
<br />A. Where permanent identification signage are provided for rooms & spaces signs shall be located on the wall
<br />adjacent to the latch side of the door.
<br />Note: Where there is no wall space on the latch side, including at double -leaf doors, signs shall be placed on the
<br />nearest adjacent wall. It is preferred on the right side, clear of any door swing.
<br />B. Tactile signs for permanent rooms are mounted on the wall at a minimum of 48" above the finish floor to the
<br />baseline of lowest tactile character and a maximum of 60" above the finish floor to the baseline of highest tactile
<br />character. Provide clear floor space of 18" minimum x 18" minimum centered on the tactile characters beyond the
<br />arc of any door swing between the closed position and 45' open position.
<br />C. The braille baseline must be betwen 48" and 60" above the finished floor.
<br />SANITARY FACILITY SIGNAGE
<br />NOTE: Sanitary facilities are required to display signs in a minimum of two locations:
<br />1. One type located on the doorway or entryway to the facility.
<br />2. One type mounted on the wall adjacent to the latch side of the door.
<br />3. 11 B-703.4.2 Restroom identification signs shall be located on the approach side of the door as one enters
<br />the room or space. .
<br />11 B-703 SANITARY FACILITY DOOR MOUNTED SIGNAGE
<br />A. 11 B-703.7.2.6.1 (Men's) - Men's sanitary facilities shall be identified by an equilateral triangle 1/4" thick with.
<br />edges 12" long and a vertex pointing upward. The triangle symbol shall contrast with the door, either light on a dark
<br />background or dark on a light background. Fig. 1 as shown on this sheet.
<br />B. 11 B-703.7.2.6.2 (Women's) - Women's sanitary facilities shall be identified by a circle that is 1/4" thick and 12"
<br />in diameter. The circle symbol shall contrast with the door, either light on a dark background or dark on a light
<br />background. Fig. 1 as shown on this sheet.
<br />C. 11 B-703.7.2.6.3 (Unisex) - Unisex sanitary facilities shall be identified by a 12" diameter circle that is 1/4" thick
<br />triangle superimposed within the circle. The triangle symbol shall contrast with the circle symbol, either light on a
<br />dark background or dark on a light background. The circle symbol shall contrast with the door, either light on a
<br />dark background or dark on a light background. Fig.1 as shown on this sheet.
<br />D. 11 B-703.4.1 - The geometric symbols shall be centered horizontally on the door at a height of 60" above the
<br />finish floor or ground surface measured to the center of the symbol. Fig. 2. as shown on this sheet.
<br />E. 11 B-703.7.2.6.4 - The edges of the signs shall be rounded, chamfered or eased, and any corners have a
<br />minimum radius of 1/8". Fig.1 as shown on this sheet.
<br />11B-703 SANITARY FACILITY WALL MOUNTED SIGNAGE
<br />A. The restroom identification signage (i.e. MEN'S, WOMEN'S, UNISEX.) is located on the wall adjacent to the
<br />latch side of the door. Fig. 2. as shown on this sheet.
<br />NOTE: Where there is no wall space on the latch side, including at double leaf door, signs shall be placed on the
<br />nearest adjacent wall, preferably on the right. Fig. 2. as shown on this sheet.
<br />B. Pictorial symbol signs (pictograms), if utilized in conjunction with verbal (i.e. text) identification, are located
<br />directly above the verbal (i.e. text) description and the border dimension of this pictogram is a minimum of 6" in
<br />height. 11 B-703.6.1 Fig.1 as shown on this sheet.
<br />C. Provide clear floor space of 18" minimum x 18" minimum centered on the tactile characters beyond the arc of
<br />any door swing between the closed position and 450 open position. Fig. 3, Fig. 4 as shown on this sheet.
<br />11B-703.7.2 - SYMBOLS OF ACCESSIBILITY
<br />1 1 B-703.7.2.1- INTERNATIONAL SYMBOL OF ACCESSIBILITY
<br />A. The International Symbol of Accessibility shall be posted to identify facilities that are accessible to and
<br />usable by physically disabled persons.
<br />B. The Symbol of shall consist of a white figure on a blue background.
<br />C. The blue color shall be equal to Color No.15090 in Federal Standard 595B.
<br />Exception: The appropriate enforcement agency may approve other colors, special signs and identification to
<br />compliment decor or unique design when it is determined that such an identification provides adequate .
<br />direction to persons with disabilities.
<br />11 B-703 - ENTRANCE SIGNS
<br />A. Entrances to buildings and facilities that are accessible to and usable by persons with disabilities shall
<br />be identified with a minimum of one International Symbol of Accessibility and with addition directional signs,
<br />utilizing the symbol, at junctions where the accessible route of travel diverges from the regular circulation
<br />path, to be visible to persons along approaching circulation paths. Fig.1 as shown on this sheet
<br />1011 EXIT SIGNS
<br />1 01 1.1 - TACTILE EXIT SIGNS
<br />A. Each grade -level exterior exit door, that is required to comply with section 1 01 1, shall be identified by a tactile sign with the
<br />word, "EXIT". Fig. 4 & 5 as shown on this sheet
<br />B. Each exit door, that is required to comply with section 1 01 1, that leads directly to a grade -level exterior exit by means of a
<br />stairway or ramp shall be identified by a tactile exit sign with following words as appropriate: Fig. 5 as shown on this sheet
<br />1. "EXIT STAIR DOWN"
<br />2. "EXIT RAMP DOWN"
<br />3. "EXIT STAIR UP"
<br />4. "EXIT RAMP UP"
<br />C. Each exit door, that is required to comply with section 1 01 1, that leads directly to a grade -level exteriorexit by means of an exit
<br />enclosure that does not utilize a stair or ramp, or an exit passageway shall be identified by a tactile exit sign with the words,
<br />"EXIT ROUTE".
<br />D. Each exit access door, that is required to comply with section 1 01 1, from an interior room (or area) that is
<br />required to have a visual exit sign shall be identified by a tactile exit sign with the words, "EXIT ROUTE".
<br />E. Each exit door, that is required to comply with section 1011, through a horizontal exit shall be identified by a tactile exit sign with
<br />the words, "TO EXIT".
<br />12" D.
<br />O O � [
<br />U � &�, - �� F°11,
<br />ICI �1111�-,-, r� co
<br />MEN WOMEN UNISEX ti
<br />0 0 0
<br />WALL-SIGNAGE DOOR MOUNTED SIGNAGE
<br />NOTE: PICTOGRAMS AN/OR LETTERING ARE NOT REQUIRED ON DOOR MOUNTED SIGNAGE.
<br />I- - - - -- -
<br />i
<br />:I
<br />I .I
<br />`�
<br />i
<br />i:
<br />�_____ - - -
<br />- --J
<br />INTERNATIONAL SYMBOL OF ACCESSIBILITY
<br />FIGURE 1 - SIGNAGE TYPES
<br />PROVIDE CLEAR FLOOR SPACE OF 18 INCHES MINIMUM X 18 INCHES MINIMUM,
<br />CENTERED ON THE TACTILE CHARACTERS BEYOND THE ARC OF ANY DOOR SWING
<br />BETWEEN THE CLOSED POSITION AND 450 OPEN POSITION.
<br />10" MAX. / 9" MIN. f .
<br />. MOUNTED 60" AFF MAX.
<br />DOOR MOUNTED SIGNAGE TO BASELINE OF
<br />HIGHTEST TACTILE
<br />CHARACTER
<br />co
<br />17
<br />7C -r--�,--
<br />RAISED EN oo o
<br />CHARACTL
<br />z
<br />ERSN w
<br />M -i
<br />BRAILLE , , . ,
<br />0
<br />FIGURE 2 - SIGNAGE FOR SANITARY FACILITIES
<br />=w
<br />2m
<br />PERMANENT SIGNAGE TO BE INSTALLED ON THE WALL
<br />ADJACENT TO THE LATCH SIDE OF THE DOOR.
<br />MOUNTING LOCATION MUST ALLOW A PERSON TO
<br />APPROACH WITHOUT ENCOUNTERING PROTRUDING
<br />OBJECTS OR STANDING WITHIN THE SWING PATH OF
<br />THE DOOR.
<br />V3�4
<br />L 0 �
<br />II �ww
<br />Z
<br />2 = Q
<br />U
<br />0 ® LL = Q
<br />¢ Z C)o wO V
<br />00 _J w co
<br />pCnJ 0ZJ
<br />w ¢ q w J i-
<br />m L 0--
<br />� � m � ¢ �--
<br />0 �m
<br />M
<br />PROVIDE CLEAR FLOOR SPACE OF 18"
<br />DOOR SWING PATH MIN. X 18" MIN. CENTERED ON THE
<br />TACTILE CHARACTERS BEYOND THE
<br />ARC OF ANY DOOR SWING BETWEEN
<br />FIGURE 3 - SIGNAGE FOR THE CLOSED POSITION AND 450 OPEN
<br />PERMANENT ROOMS AND SPACES POSITION.
<br />LETTERING RAISED
<br />1 /32"
<br />- E
<br />- - i -
<br />ROOM 7
<br />.234
<br />(braille grid) LITERARY BRAILLE
<br />00 00 00 00 00 00 00 00 00 00 STANDARD DIMENSIONS:
<br />00 00 00 00 00 00 00 00 00 00
<br />00 00 00 00 00 00 00 00 00 00
<br />a b c Dot diameter 0.059 inches
<br />LETTERS AND NUMBERALS SHALL BE RAISED Inter -dot spaceing 0.090 inches
<br />1/32", UPPER CASE, SAN SERIF TYPE AND.
<br />SHALL BE ACCOMPANIED WITH GRADE II Horizontal separation
<br />BRAILLE. RAISED CHARACTERS SHALL BE AT between cells 0.241 inches
<br />LEAST 5/8" HIGH, BUT NO HIGHER THAN 2
<br />Vertical separation
<br />FIGURE 3 - CONTINUED between cells 0.395 inches
<br />DOOR SWING PATH e
<br />FIGURE 4 - TACTILE EXIT SIGN
<br />c
<br />w
<br />J
<br />- 0 F=
<br />D F= ~ U .
<br />5 ~ 1E Cn
<br />Lww Lw -
<br />iiv =
<br />11 )0 cc�<
<br />LL 0 =
<br />L p i F- w U
<br />- w U Z Z
<br />D w 2i U)
<br />5 S`
<br />... m PROVIDE CLEAR FLOOR SPACE OF 18„
<br />MIN. X 18" MIN. CENTERED ON THE
<br />TACTILE CHARACTERS BEYOND THE
<br />ARC OF ANY DOOR SWING BETWEEN
<br />THE CLOSED POSITION AND 450 OPEN
<br />POSITION.
<br />6" (TYP.)
<br />I, EQ
<br />WORDING AS
<br />PER
<br />APPROPRIATE
<br />CONDITION - - ----E %O �
<br />\K--- Al I
<br />DISTANCE :2�
<br />BETWEEN BRAILLE =
<br />AND OTHER 00
<br />TACTILE ELEMENTS
<br />(BRAILLE)
<br />DISTANCE FROM
<br />RAISED BORDER
<br />AND DECORTIVE
<br />ELEMENTS z
<br />co
<br />`. CC 9, A I M I
<br />PERMIT SUBMITTAL �o
<br />. .
<br />08/01/2022 , ( ,
<br />- I . 22-5704-01
<br />n
<br />PM: KEVIN MARX
<br />`') . DRAWN: RM
<br />
|