3620 W MUKILTEO BLVD F HARBORS EDGE TOWNHOMES 2025-08-13

Viking Plastics BlazeMastere CPVC Pipe MA& CPVC Pipe Product Specifications Corrosion resistant CPVC fire sprinkler pipe, when installed in strict accordance with the manufacturer's design and instal- lation instructions, is UL and aUL Listed by Underwriters Laboratories for use in the following: • Meets NFPA 1 ME and 1 So standards for residential occupancies as well as NFPA 13 standards for light hazard occupancies. • Residential occupancies up is and including four stories in height as defined by N EPA 13P • Residential occupancies as defined n the Standard for Sprinkler Systems in One and Two Family Dwellings, NFPA 1 So. • Installation of private fire service mains and their appurtenances, N EPA 24. CPVCfire sprinkler pipe from Viking Plastics shall be employed in wet pipe systems only and are not listed for outdoor use. CPVC pipe must never be used in a system using compressed air or other gases CPVC pipe from Viking Plastics also carries the follow- ing enhanced listings and approvals: According to U LLsting • Can be flush at return air plenums • Exposed system risers NFPA 15o,13P • Exposed basement NFPA 13D (solid woodJoist) • Extended coverage (exposed) • 20'spacing on pendent in lieu of 15' • 15'spacing on sldewall In lieu of 14' • Use with combustible concealed spnnklers • red amc sprinkler head (to pm@cttifenmr below) • red amc sprinkler head with wet system piping (feed main and ridge Installation) New and enhanced listings and approvals are being pursued Always check with the appropriate Listing andAppmval agency for details on current lining parameters CPVC pipe meets all applicable standards for pressure rated applies for as required In ANSI CST Standard 14 and complies with ANSI CST Standard 61 for health effects and are marked with the CST do anti use marking At CHAD fire sprinkler pipe shall be Listed by Underwriters Laboratories forwet pipe systems, and shall carry rated working pressure of 175 pa @ 150°F (12 bar@ 655°C).'The FMAppmval Is limited to use In wet pipe fire protection sprinkler systems for light hazard occupancies In both concealed and exposed applications with curtain restrictions. Piping must always be Installed In arid accordance to the manufacturer's DESIGN AND INSTALLATION GUIDE Including product storage and handling, joining methods, suppohlug and bracing, expansion and coo- tradier allowance and resume, ern National Fire Protection Association (NFPA1 Standards 13,13D, and 13P must be referenced for design and installation requirements in conjunction with the installation instructions Exposed sldewall sprinkler listing for exposed pipe & fittings • 24extended coverage sldewall sprinkler, 12" dmp, 155°F sprinkler head • 15' extended coverage sldewall sprinkler, 12" dmp, 165°F sprinkler head • 16' extended coverage sldewall sprinkler 12" dmp, 175°F sprinkler head • 14'standard coverage sidewall sprinkler, 12' drop , Zoo°F sprinkler head Factory Mutual Appmved' • Factory Mutual Approval exposed • Factory Mutual Approval above tlmp in ceilings • Factory Mutual Approval exposed w/SoflFSteel soflltlng covering system All CPVC fire sprinkler pipe from Viking Chancels manufactured In the USA At CPVC pipe shall be packaged immediately after its manufacture to prevent damage and shall be stored indoors after production, at the manufacturing site until shipped from the factory. The pipe shall bear the logo of the lining agendas, and shall curry the National Sanitation Fourr nation (NSF) seal of approval for potable water applications CPVC products are intended for use In areas where the maximum ambi ant temperature does not exceed 150°F @55°C). If the ambient tempera wra is expected to exceed this limitation, refer to the manufacturer's OF SIGN AND INSTALLATION GUIDE for additional information on methods to reduce the pipe exposure temperatures CPVC pipe is not intended to be installed In outdoor applications. CPVC pipe Is intended to be used In wet pipe systems only and have not been investigated for use In dry pipe systems. Special Installation and design criteria relative to pipe hanger spacings, piping and sprinkler restraint, sprinkler temperature rating, piping locations, testing procedures and fiction lass characteristics are specified in the manufacturer's installation Instructions provided with the pipe. The manufacturer's Installation Instructions should be reviewed and the Authority Having Jurisdiction consulted before installation. Trusted above all" NIKING°