Laserfiche WebLink
it <br />ss <br />81 <br />2018 IBC/NDS 2015 - Shear Wall Framing Clips <br />Model <br />No. <br />Type of <br />connection <br />Fasteners <br />(in.) <br />' Direction <br />of Load <br />DF/SPAllowable Leads ( <br />SPF/HFAllowable Loads <br />Floor <br />(100) <br />Hoof <br />(125) <br />(160} : <br />Floor <br />(100) <br />Roof <br />(125) <br />(160) <br />(8) 0.131 x 1 Y2 <br />Fr <br />395 <br />465 <br />41_ <br />340 <br />400 <br />F26 <br />--- <br />395 <br />430 <br />— <br />430 <br />340 <br />_ _o . <br />;r/ <br />�/0 <br />A34 <br />0 <br />(8) #9 x 1'12 SD <br />F1 <br />640 <br />640 <br />640 <br />550 <br />550 <br />550 <br />F2 <br />9E <br />495 <br />496 <br />425 <br />425 <br />425 <br />Uplift <br />240 <br />240 <br />240 <br />170 <br />170 <br />170 <br />[2 � <br />(9) 0131 x 1 Ys <br />Al <br />295 <br />350 <br />350 <br />255 <br />300 <br />200 <br />E <br />295 <br />360 <br />385 <br />255 <br />310 <br />330 - <br />C1 <br />186 <br />185 <br />]85 <br />160 <br />160 <br />160 <br />Q <br />(12) 0,131 x 1'/s <br />A2 <br />295 <br />325 <br />325 <br />255 <br />280 <br />280 <br />Cp <br />295 <br />-330 <br />330 <br />255 <br />265 <br />285 <br />D <br />2255 <br />225 <br />225 <br />195 <br />195 <br />195 <br />(12) fl�l3x 1'/2 <br />F1 <br />590 <br />650 <br />650 <br />510 <br />560 <br />F2 <br />670 <br />510 <br />575 <br />575 <br />(12) PH6121 <br />I F1 <br />420 <br />420 <br />420 <br />360 <br />360 <br />360 <br />- <br />(12) 0.131 x 11120 <br />5-80 <br />t <br />::H <br />580 <br />615 <br />525 <br />500 <br />a5 <br />450 <br />(12) 0.131 x 1112 <br />G <br />580 <br />565 <br />565 <br />500 <br />485 <br />485 <br />H <br />545 <br />490 <br />490 <br />470 <br />420 <br />n20 <br />1. Allowable loads are for one angle. When angles are installed on each side of the joist, the minimum joist thickness is 3". <br />2. Some illustrations show connections that could cause cross -grain tension or bending of the wood during loading if not <br />reinforced sufficiently. In this case, mechanical reinforcement should be considered. <br />3. LTP4 can be installed over 3/8" wood structural panel sheathing with 0.131" x 1 1/2" nails and achieve 0.72 of the listed load, <br />or over 1/2" sheathing and achieve 0.64 of the listed load. 0.131" x 2 1/2" nails will achieve 100% load. <br />4. LTP4 satisfies the IRC continuously sheathed portal frame (CS-PF) framing anchor requirements when installed over raised <br />wood floor framing per Figure R602.10.6.4. <br />5. The LTP5 may be Installed over wood structural panel sheathing up to 1/2" thick using 0.131" x 1 1/2" nails with no reduction <br />in load. <br />6. Connectors are required on both sides to achieve F2 loads in both directions. <br />7. Fasteners: Nail dimensions in the table are diameter by length. SD screws are Simpson Strong -Tie° Strong -Drive® screws. <br />PH6121 is a pan -head #6 x 1/2" screw available from Simpson Strong -Tie. For additional information, see Fastener Types and <br />Sizes Specified for Simpson Strong -Tie Connectors. <br />51 e;.�1 <br />t-' i fit`'=1 i1Ci1 <br />t P <br />AY+ Y�ittlCl�+t.VJSIS'hUOi�PI)(ICI�}�YP;$�i�l.It1g <br />t V' <br />J <br />c,i� <br />ti <br />\ yvi <br />L3.3 <br />