3003 W CASINO RD BLDG 40-58 2025-09-29

Seismic Bracing TOLCOT" Fig. 828 - Universal Sway Brace Attachment to Steel (FM Approved) Size Range: One size accommodates all sway Fig.900 Series brace OPM �M Y I 3 7 O attachments. Fits from /8" 19.4mm)to /8" (22.2mm)thick steel structure. For thicknesses APPROVED less than 3/8" (9.4mm)refer to Fig.825. j Material: Steel cone Point Function: To attach sway bracing and/or hangers to various types of steel structural 4colie et Bolts A members.Features: Permits secure non-friction connection without drilling or welding. Uniquesot sops design allows offset placement on wide flange beam, I-beam,C-channel,open web, Included welded steel trusses, etc.. Secures brace to structure either across or along the beam. Break-off set bolts allow for visual verification of proper installation torque. Approvals: Factory Mutual Approved(FM). Included in our Seismic Engineering Guidelines approved by the State of California Office of Statewide Health Planning and Development(OSHPD). For additional load, spacing and placement information relating to Point OSHPD projects, please refer to our Seismic Engineering Guidelines, OPM-0052-13. Set Bolt B For UL Listed information refer to UL Listed page 52, Installation Instructions: The Fig.828 is the structural attachment component of a longitudinal or lateral sway brace assembly. It is intended to be combined with a TOLCO transitional attachment,'bracing pipe"and a TOLCO'braced pipe'attachment to form a complete bracing assembly. NFPA 13 or FM guidelines should be followed. To Install: Place the Fig.828 on the flange of the beam,truss, or girder. Be sure the attachment is fully engaged to the rear of the opening.Tighten the cone point set bolts(A) until the heads break off.Tighten the cone point set bolt 113)until the head breaks off. r Remove the flange nut from set bolt(B). Install a TOLCO swivel fitting Fig.980 or any other TOLCO approved transitional fitting). 1 Use flange nut to secure the swivel fitting'. Finish: Plain or Electro-Galvanized Approx.Weight/100: 275 Lbs. (124.7ky) F '.Order By: Figure number and finish Patent tf6,098,942,#8,534,625 Canada Patent#2,286,659 Patent Pending Designed to meet or exceed requirements of FM DS 2-8. ' Retaining strap not required. FM Approved Allowable Horizontal Load* -----.-----, ______________ With Brace Perpendicular To Beam 1 ! Brace Angle degrees front vertical) 30'-44° y 450-590 60°-74° 75*-900 ..........___ _............................._._.........._...._._._.._.__.... ..... Fig.828 ; 1570 2220 1210 700 y t__ }_________ ... (8.98kN1 JUAN) 15.38kN) (3.11kN) e Fig.828 Shown with - May pivot in any FM Approved Allowable Horizontal Load' Fig 3B0 direction With Brace Parallel To Beam shown with Brace Angle Idegrees from vertical) Fig.980 30'-44° 45°-59* 600-740 75°-90° ...................................... .. ................................................. 690 970 1210 1330 (3.07kN) (4.3lkN) (5.38kN) (5.9lkN1 FM Approved design loads are based on ASD design method. Eaton's B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components, resulting in a listed seismic bracing assembly.Eaton B-Line Division warranty for seismic bracing components will be the warranty provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton,except that,in addition to the other exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are combined with products not provided by Eaton. Al dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise specified. . ................_.............. . ........_.._................._._._.......... B-Line series Fire Protection Solutions 53 Eaton