Laserfiche WebLink
SERIES <br /> 6 Amp and 10 Amp, 24 Volt Power Supplies <br /> The PS Series are independently configurable <br /> power supplies, allowing you to pair any input <br /> with any output, and feature LED diagnostics <br /> for troubleshooting. <br /> The PS Series is a remote power supply line from Honeywell Power Products and is a direct <br /> replacement for the HPF-24S6/8.The HPF-PS6 is a 6 amp and the HPF-PS10 is a 10 amp, <br /> remote power supply with battery charger that maybe connected to any 12 or 24 volt fire <br /> alarm control panel(FACP)or used as a standalone power supply.The PS Series provides 24 <br /> VDC power for NACs(notification appliance circuits)configured as either Class B or Class A <br /> (requires the ZNAC-PS option card)with multiple sync protocol options.The PS Series also <br /> provides auxiliary power,constant or resettable,suited for detectors,annunciators,door <br /> holders,and other fire alarm system peripherals.The PS Series cabinet can hold two 7 AH or <br /> 18 AH batteries and can charge up to 33 AH batteries in a separate cabinet.The HPF-PS6E <br /> and HPF-PS10E are models rated for 240V operation. <br /> FEATURES AND BENEFITS <br /> HPF-PS61101E <br /> • Up to five(6 amp model)or seven(10 amp • 6 or 10 amp full load output,respectively, <br /> model)independently-configurable,power- with 3 A maximum/circuit <br /> limited output circuits for: • Individual NAC power and trouble LEDs for <br /> —Class B and/or Class A NACs diagnostic efficiency <br /> —Class B and/or Class A resettable or non- • Trouble history mode for diagnostic support <br /> resettable 24V auxiliary power • Wide range end-of-line supervision value <br /> —door holder power (normal:2-27K ohms) <br /> • Converts from Class B to Class A wiring • Selectable earth fault detection(enable or <br /> without losing any outputs using the ZNAC- disable) POWER SUPPLY <br /> PS converter card(sold separately) • AC trouble report delay timer <br /> • Optimal for powering four-wire smoke • Completely configurable via onboard DIP <br /> detectors,annunciators,and other system switches,no extra software required <br /> peripherals requiring regulated power • Self-contained in compact,locking cabinet <br /> • Optional addressable control,monitor,and constructed of heavy gauge steel with a <br /> relay modules and power-supervision relay corrosion-resistant powder coat chip and <br /> (EOLR-1) scratch-resistant finish <br /> • Configurable for ANSI°Temporal or • Cabinet designed with ten double <br /> Temporal 4 coded output knockouts and a removable door for ease of <br /> • UL-Listed NAC synchronization using installation and wiring HPF-PS6E/10B/E <br /> System Sensor',Wheelock',Gentex°,or • Includes integral battery charger capable of <br /> AMSECO°appliances charging up to 33 AH batteries <br /> • Synchronization can be triggered from • Cabinet can house two 7 AH or 18 AH <br /> FACP NAC/remote sync outputs,cascaded batteries <br /> power supply,or a control module,single or • Battery charger may be disabled via DIP <br /> multi,which may be housed within the switch for applications requiring larger <br /> power supply cabinet batteries and external battery charger <br /> • Ability to cascade up to four power supplies • Removable terminal blocks accommodate <br /> • Two(6 amp mode[)or three(10 amp mode[) up to 12 AWG(3.1mm2)wire <br /> fully-isolated input/control circuits which • Works with any UL 864 FACP which utilizes <br /> can be programmed to any output an industry-standard reverse-polarity <br /> • Two Form C normally-closed trouble relays notification circuit <br /> for AC Trouble and General Trouble Honeywell <br />