6801 SEAWAY BLVD 2024 MCKESSON CORP 2025-09-12

Signature Series Overview UIO Motherboard The Signature Series intelligent analog addressae system from 1 s-a� 9 9 g- bl t f y Self-tapping Kidde Security is an entire family of multi-sensor detectors and screws --------- - mounting bases, multiple-function input and output modules, _ network and non-network control panels, and user-friendly mainte- -.04 Plug-in(UIO) >Captive nance and service tools.Analog information from equipment con- Module screws nected to Signature devices is gathered and converted into digital __ __ F_Ut signals.An onboard microprocessor in each Signature device fi Fla-----washers measures and analyzes the signal and decides whether or not to input an alarm.The microprocessor in each Signature device pro- vides four additional benefits—Self-diagnostics and History Log, Cabinet or electrical enclosure Automatic Device Mapping, and Fast,Stable Communication. Self-diagnostics and History Log—Each Signature Series Electronic Addressing -The loop controller electronically ad- device constantly runs self-checks to provide important mainte- dresses each module, saving valuable time during system com- nance information.The results of the self-check are automatically missioning. Setting complicated switches or dials is not required. updated and permanently stored in its non-volatile memory.This Each module has its own unique serial number stored in its information is accessible for review any time at the control panel, on-board memory.The loop controller identifies each device on PC, or using the Signature Program/Service Tool. the loop and assigns a"soft"address to each serial number. If Automatic Device Mapping—The Signature Data Control- desired,the modules can be addressed using the Signature Pro- ler(SDC)learns where each device's serial number address is gram/Service Tool. installed relative to other devices on the circuit.The SDC keeps a Kidde recommends that this module be installed according to lat- map of all Signature Series devices connected to it.The Signature est recognized edition of national and local fire alarm codes. Series Data Entry Program also uses the mapping feature.With interactive menus and graphic support,the wired circuits be- tween each device can be examined. Layout or"as-built"drawing Application information showing branch wiring(T-taps), device types and their address are stored on disk for printing hard copy. The duty performed by the GSA-CT1 and GSA-CT2/MCT2 is de- termined by their sub-type code or"Personality Code".The code is selected by the installer depending upon the desired application Installation and is downloaded from the loop controller. GSA-CTi,GSA-CTi HT and GSA-CT2: modules mount to North One personality code can be assigned to the GSA-CT1.Two per- American 21/2 inch(64 mm)deep 1-gang boxes and 11/2 inch(38 sonality codes can be assigned to the GSA-CT2/MCT2. Codes mm)deep 4 inch square boxes with 1-gang covers and GSA-MP 1, 2,3 and 4 can be mixed on GSA-CT2/MCT2 modules only. For mounting plates.The terminals are suited for#12 to#18 AWG(2.5 example, personality code 1 can be assigned to the first address mm2 to 0.75 m ire size. (circuit A)and code 4 can be assigned to the second address / Compatible electrical box (Circuit B). f NORMALLY-OPEN ALARM -LATCHING(Personality Code 1) -Assign to one or both circuits. Configures either circuit A or B or both for Class B normally open dry contact initiating devices such as Pull Stations, Heat Detectors, etc.An ALARM signal is sent to Wall plate,white the loop controller when the input contact is closed.The alarm (1-gang) condition is latched at the module. m NORMALLY-OPEN ALARM - DELAYED LATCHING (Person- ality Code 2)-Assign to one or both circuits. Configures either mm circuit A or B or both for Class B normally-open dry contact initiat-ing devices such as Waterflow Alarm Switches.An ALARM signal ., is sent to the loop controller when the input contact is closed for Status LEDs approximately 16 seconds.The alarm condition is latched at the a module. LED viewing ports • ' NORMALLY-OPEN ACTIVE- NON-LATCHING (Personality o, Code 3)-Assign to one or both circuits. Configures either circuit A or B or both for Class B normally-open dry contact monitoring L11 ® input such as from Fans, Dampers, Doors, etc.An ACTIVE signal GSA-MCT2:mount the UIO motherboard inside a suitable Kidde is sent to the loop controller when the input contact is closed.The enclosure with screws and washers provided. Plug the GSA- active condition is not latched at the module. MCT2 into any available position on the motherboard and secure NORMALLY-OPEN ACTIVE- LATCHING (Personality Code the module to the motherboard with the captive screws.Wiring 4)-Assign to one or both circuits. Configures either circuit A or connections are made to the terminals on the motherboard(see B or both for Class B normally open dry contact monitoring input wiring diagram). UIO motherboard terminals are suited for#12 to such as from Supervisory and Tamper Switches.An ACTIVE signal #18 AWG(2.5 mm2 to 0.75 mm2)wire size. is sent to the loop controller when the input contact is closed.The active condition is latched at the module. Page 2 of 4 DATA SHEET K85001-0241 Not to be used for installation purposes. Issue 1