3003 W CASINO RD BLDG 40-27 2025-09-09

Product Overview — (continued) Model ZIC-4A contains a microprocessor which Leased Line—Each of the four(4)circuits on Model ZIC-4A allows notification-circuit outputs to function in a can be configured for connection to a leased line.The degrade mode —even if the main FireFinder XLS circuits can be programmed to transmit Alarm, processor or the local-network communication link Supervisory, or Trouble signals. A leased-line module has failed. In a degrade mode, Model ZIC-4A will (Model LLM-1) is required for this feature. respond to an Alarm or Trouble from any intelligent-addressable initiating device or Bell Follower—Each of the four(4)circuits on Model conventional-zone initiating device connected in ZIC-4A can be configured as a NAC that can follow the input the same local enclosure. from another NAC in an external fire-alarm control Standard NAC zone—Each of the four(4)circuits on panel. Circuit 1 on a Model ZIC-4A card within a Model ZIC-4A can be configured for use as a FireFinder XLS system enclosure can be configured as the standard Notification Appliance Circuit. The NAC Bell Follower—Master and is connected to the external output can be used as a steady, strobe- NAC. synchronized, or zone-coded output. Available Any other ZIC-4A circuit in that enclosure can be coding includes ANSI Temporal, March Time 120- configured to follow the state of the Master. This feature pulse-per-minute (PPM), March Time 60 PPM, can be used to synchronize coded or ANSI Temporal patterns March Time 30 PPM, Canadian Two-stage 30 PPM, for audible sounds with another fire-alarm control panel. Canadian Two-stage 120 PPM and custom coding. Outputs may be programmed through logic to transmit up to three (3) different signal types, Controls and Indicators depending on event priority. For instance, the same RESET switch Re-initializes Model ZIC-4A card only circuit can be programmed to transmit the ANSI Temporal pattern for evacuation, March Time 120 POWER LED Indicates that power is applied to PPM for tornado notification, and a custom code for Model ZIC-4A recall. CARD-FAIL LED Illuminates when the card Standard speaker zone—Each of the four(4)circuits microprocessor has failed on Model ZIC-4A can be configured for use as a CAN-FAIL LED Illuminates when the CAN standard speaker circuit in single or dual-channel communication fails and Model ZIC- systems. Model ZIC-4A can be used with the Model 4A is in degrade mode ZAM-180 bulk amplifier, or Model ZAC-40 amplifier card. Each circuit on Model ZIC-4A is limited to 96 HNET-FAIL LED Illuminates when the HNET Watts per zone. communication fails and Model ZIC- Releasing zone— Each of the four (4) circuits on 4A is in degrade mode Model ZIC-4A can be configured for use as a releasing GND-FAULT LED Indicates the detection of a ground- circuit.This circuit can be used to release FM-200. fault condition (either negative or For proper supervision of a releasing circuit,the Model positive) on the field wiring of REL-EOL module must be used. Model REL-EOL can Model ZIC-4A use power directly from the FireFinder XLS system. ZONE-ACTIVE Illuminates to indicate that the zone No external, regulated power supply is required. LEDs has been activated either Municipal Tie—Each of the four(4)circuits on Model automatically or manually. There is ZIC-4A can be configured so that it can be connected one (1) LED for each zone. to and activate a municipal city tie box. The circuit TROUBLE LEDs Indicates the presence of a Trouble meets the requirement of some jurisdictions to allow condition (either an open circuit or the box to be reset before the fire-alarm control panel. a short circuit) on the zone. A leased-line module (Model LLM-1) is required for this There is one (1) LED for each feature. zone. SIEMENS Industry, Inc. Building Technologies Division