1605 SE EVERETT MALL WAY WALMART 2025-09-10

TFP336 Page 2 of 2 1 - Frame 3 - Sealing 4 - Bulb 6 - Compression 2 - Button Assembly 5 - Deflector Screw 6 WRENCH 5 FLAT 4 1/2" \ WRENCH 3 (12,7 mm) 2-3/8" RECESS NOMINAL (60,3 mm) 2 MAKE-IN 1 ll, 3/4" NPT f FIGURE 2 W-TYPE 8 FIGURE 1 SPRINKLER WRENCH MODEL TY7158 STANDARD COVERAGE, UPRIGHT STORAGE SPRINKLER, 16.8 K-FACTOR Li rr ited TY7158 Sprinkler, the diameter of the Care and Warranty air bubble is approximately 1/16 in. (1,6mm). Maintenance For warranty terms and conditions,visit A leak tight 3/4 in. NPT sprinkler joint www.tyco-fire.com. should be obtained by applying a min- The TYCO Model TY7158 Standard imum-to-maximum torque or 10 to 20 Coverage Upright Sprinkler must be Ordering lb-ft (13,4 to 26,8 N•m). Higher levels maintained and serviced in accordance of torque may distort the sprinkler inlet with this section. Procedure with consequent leakage or impair- Before closing a fire protection system ment of the sprinkler. Only the W-Type main control valve for maintenance When placing an order, indicate the full 8 Sprinkler Wrench(Ref. Figure 2)shall work on the fire protection system product description and Part Number be used during installation. that it controls, obtain permission to (P/N). Sprinkler Installation shut down the affected fire protection Sprinkler Assembly Install the Model TY7158 Upright Sprin- system from the proper authorities Specify: Model TY7158 Standard Cov- kler only in the upright position as and notify all personnel who may be erage Upright Sprinkler, SIN TY7158, follows: affected by this decision. temperature rating (specify), P/N Step 1. Apply pipe-thread sealant to Inspection, testing, and maintenance (specify): sprinkler threads. must be performed as indicated below 155°F(68°C) ................ 51-901-1-155 Ste 2. Hand-tighten sprinkler into and in accordance with the local 200°F(93°C). ...............51-901-1-200 p g p requirements and/or national codes. 286°F(141°C)`...............51-901-1-286 sprinkler fitting. Do not apply force to Any impairment must be immediately *Fire testing of the TYCO Model TY7158 Sprinkler was glass bulb, grasp only by wrench flats corrected. completed only in the 155°F(68°C)temperature rating. while hand-tightening. The results of such fire testing is outlined in UL Test Re- 3. Wrench tighten the Model The owner is responsible for the port NumberNC27954. Step Step 3 sprinkler 1-1/4 to the turns inspection,testing,and maintenance of Sprinkler Wrench beyond hand-tightening or by applying their fire protection system and devices Specify: W-Type 8 Sprinkler Wrench, in compliance with this document, as P/N 56-892-1-001 a minimum-to-maximum torque of 10 well as with the applicable standards e a ing eats to 26,8 wrench by fully of any authorities having jurisdiction. engaging (seating) the wrench on the Contact the installing contractor or the sprinkler is(Ref. Figure 1)using only product manufacturer regarding any the W-Type 8 Sprinkler Wrench (Ref. questions. Figure 2). Automatic sprinkler systems are rec- ommended to be inspected, tested, CEM Higher levels of torque may distort and maintained by a qualified Inspec- sprinkler inlet with consequent leakage tion Service in accordance with local or impairment of sprinkler. requirements and/or national codes. 1400 Pennbrook Parkway,Lansdale,PA 19446 1 Telephone+1-215-362-0700 m 2018 Johnson Controls.All rights reserved.All specifications and other information shown were current as of document revision date and are subject to change without notice. Johnson 1 nson ORO NATIONAL FIRE PROTECTION ASSOCIATION Is a registeretl tratlemark of National Fire Protection Association; Controls TEFLON Is a registeretl tratlemark of DuPont