1605 SE EVERETT MALL WAY WALMART 2025-09-10

Seismic Bracing Fig. 980-TOLCO Universal swivel sway brace attachment-3/8"-16 to 3/4'-10 rods Fig. 980H -TOLCO Universal swivel sway brace attachment-1/8'-9 to 11/4"-7 Size Range: One size fits bracing pipe 1" (25mm)thru 2" (5omm), B-Line series O 12 gauge (2.6mm) channel. FM Material: Carbon steel OPM APPROVED Function: Multi-functional attachment to structure or braced pipe fitting. Features: This product's design incorporates a concentric attachment opening which is critical to the performance of structural seismic connections and in accordance with NFPA 13, 2019 Section 18.5.11.5. The Fig. 980 mounts to 980 any surface angle and the break off bolt head assures verification of proper ' installation. o Installation: Fig.980 is the structural or transitional attachment component of a J 9� longitudinal or lateral sway brace assembly. It is intended to be combined with B the "bracing pipe" and TOLCO'" "braced pipe" attachment, Fig. 1000, 1001, A 3000,4L, or other TOLCO approved attachment to pipe to form a complete bracing assembly. NFPA 13 guidelines should be followed. set Bolt Mounting Hardware To Install: Place the Fig. 980 onto the "bracing pipe".Tighten the set bolt until Included Is Not Included the head breaks off. Attachment can pivot for adjustment to proper brace angle. Approvals:—Approved by Factory Mutual Engineering(FM). Included in our Seismic Engineering Guidelines approved by the State of California Office of Statewide Health Planning and Development(OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to our Seismic Engineering Guidelines, OPM-0052-13. For UL Listed information refer to UL Listed page 60. `► Note: Fig. 980 Swivel Attachment and Fig. 1000, 1001, 4L or other TOLCO approved attachment to pipe that make up a sway brace system of bracing materials which satisfies the requirements of Factory Mutual Engineering and the National Fire Protection Association (NFPA) Finish: Plain, EIectro-Ga Ivan ized or Stainless Steel. Fig.980 Contact customer service for alternative finishes. ®R a Order By: Figure number and finish. Fig 1001 \ Pat. #6,273,372, Pat. #6,517,030, Pat. #6,953,174, Fig.980 Pat. #6,708,930, Pat. #7,191,987, Pat. #7,441,730,Pat. #7,669,806 `/ Designed to meet or exceed requirements of FM DS 2-8. " Fig.4L Brace Longitudinal Lateral Brace Brace A B D** Max. Design Load*** (FM) Approx.W000 Catalog# in. (mm) in. (mm) in. (mm) 30°-44° 45°-59° 600-740 750-900 Ibs. (kg) Ibs./(kN) Ibs./(kN) Ibs./(kN) Ibs./(kN) 980-3/8 7/16 (11.1) 149 (67.6) 980-'/2 1/,s (14.3) 2370 2790 3360 3750 148 (67.1) 98U 5/8 49/16 (114.9) 2'/16 (52.4) 11/16 (17.5) (10.54) (12.41) (14.94) (16.68) 147 (66.7) 980 3/4 13/16 (20.6) 146 (66.2) 980H 7/8 15/16 (23.8) 402 (182.3) 980H-1 11/16 (27.0) 400 (181.4) 63/4 (171.4) 31/2 (88.9) Fig.980H is not UL Listed 980H-1'/8 13/16 (30.2) or FM Approved 397 (180.1) 980H-1'/4 15/16 (33.3) 390 (176.9) **Mounting attachment hole size. ***Installed with 1"or 11/4"schedule 40 brace pipe. Eaton's B-Line series seismic bracing components are designed to be compatible only with other B-Line series bracing components, resulting in a listed seismic bracing assembly. Eaton B-Line Division warranty for seismic bracing components will be the warranty provided in Eaton B-Line Division standard terms and conditions of sale made available by Eaton,except that, in addition to the other exclusions from Eaton B-Line Division warranty, Eaton makes no warranty relating to B-Line series seismic bracing components that are combined with products not provided by Eaton. All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Fire Protection Solutions 61 Eaton