Laserfiche WebLink
i <br />mi <br />FBI, <br />1/4 #1=1 I—Ops <br />SECOND FLOOR ELECTRICAL PLAN <br />REGISTERS IN CEILING <br />THIS PLAN U.N.O. <br />ELECTRICAL LEGEND <br />DUPLEX RECEPTACLE OUTLET <br />DUPLEX RECEPTACLE OUTLET <br />SPLIT WIRED (SWITCH TOP HALF) <br />MWo DUPLEX RECEPTACLE OUTLET <br />MICROWAVE <br />SINGLE RECEPTACLE OUTLET <br />208v (R: RANGE, D: DRYER) <br />Q <br />JUNCTION BOX <br />SINGLE POLE SWITCH <br />$3 <br />THREE WAY SWITCH <br />DIM.$ <br />DIMMER SWITCH <br />$T <br />TIMER SWITCH <br />24 HR CLOCK TIMER - <br />AUTOMATIC <br />SMALL FLUORESCENT <br />STRIP LIGHT <br />PPENDANT <br />LIGHT <br />0 <br />HOSE <br />BIBB <br />ELEC <br />METER <br />00 <br />4 <br />DIRECTIONAL INCANDESCENT <br />HEAT LAMP, EXHAUST <br />CEILING MOUNTED LIGHT <br />FAN COMBINATION RECESSED <br />CEILING FIXTURE - 250W LAMP <br />INCANDESCENT RECESSED <br />50 CFM MIN, 4,0 SONES, <br />CEILING LIGHT <br />4" ROUND DUCT <br />INCANDESCENT WALL <br />RECESSED CEILING <br />MOUNTED LIGHT <br />EXHAUST FAN <br />50 CFM MIN, 1.5 SONES, <br />O <br />DOUBLE TUBE FLUORESCENT <br />4" ROUND DUCT <br />CEILING MOUNTED LIGHT <br />L M J <br />MICROWAVE OVEN/RANGE <br />HOOD COMBINATION - <br />MW <br />EXHAUST FAN TO PROVIDE <br />H <br />RECESSED HEAT LAMP - <br />A MIN. OF 100 CFM. <br />NUTONE 9410H, 250W LAMP <br />CEILING FIXTURE <br />CENTER <br />INCANDESCENT CEILING <br />ELECTRICAL PANEL <br />MOUNTED LIGHT <br />0 <br />THERMOSTAT <br />© <br />CARBON MONOXIDE <br />® <br />SMOKE DETECTOR <br />DETECTOR <br />FLOOR REGISTER <br />RECESSED CEILING WHOLE HOUSE <br />EXHAUST FAN MEETING CFM <br />TEL V <br />TELEPHONE JACK <br />WHF <br />REQUIREMENTS OUTLINED IN IRC <br />TV <br />TELEVISION JACK <br />SECTION M1057.3. <br />Ilk <br />. <br />1 <br />ABOVE SLAB ABOVE SLAB <br />ELEVATION OF ELECTRICAL OUTLETS A.F.F. <br />AT KITCHEN REVISED. <br />` r <br />1 <br />1/4"=1'-0" <br />GENERAL NOTES <br />FIRST FLOOR ELECTRICAL PLAN <br />THIS ELECTRICAL PLAN IS THE ARCHITECT'S SUGGESTED <br />LAYOUT. THE ELECTRICAL CONTRACT IS ON A DESIGN -BUILD <br />BASIS. ELECTRICAL CONTRACTOR'S DESIGN SHALL BE <br />APPROVED BY THE OWNER AND SHALL CONFORM TO THE <br />APPLICABLE ELECTRIC CODE REGARDLESS OF WHAT IS SHOWN <br />ON THIS DRAWING. <br />ALL SWITCHES, OUTLETS AND ENVIRONMENTAL CONTROLS <br />SHALL BE MOUNTED NOT LESS THAN 15" NOR MORE THAN 48" <br />ABOVE FINISHED FLOOR AND SHALL BE. ALIGNED VERTICALLY. <br />APPLIANCES DESIGNED TO BE FIXED IN POSITION SHALL BE <br />SECURELY FASTENED IN PLACE. <br />WATER HEATERS SHALL BE ANCHORED OR STRAPPED AT <br />POINTS WITHIN THE UPPER 113 OR LOWER 1/3 TO RESIST <br />EARTHQUAKE MOTION. <br />LIGHT FIXTURES THAT SERVE TO ILLUMINATE INTERIOR STAIRS <br />SHALL BE LOCATED IN THE IMMEDIATE VICINITY OF EACH STAIR <br />LANDING AND SHALL PROVIDE A MIN. LIGHTING LEVEL OF 1 <br />FOOT-CANDLE MEASURED AT CENTER OF TREADS AND <br />LANDINGS PER IRC R303.7. <br />ENERGY NOTES <br />SEE ENERGY NOTES ON SHEET D1. <br />FURNACE AND WATER HEATER SHALL BE FUELED BY <br />NATURAL GAS. THE PILOTS, BURNERS, HEATING ELEMENTS <br />AND SWITCHES SHOULD BE A MINIMUM OF 18" ABOVE THE <br />GARAGE FLOOR. <br />REGISTERS IN CEILING <br />THIS PLAN U.N.O. <br />DUCT AND VENTILATION NOTES <br />VENTILATION: SEE NOTES ON COVER SHEET. <br />KITCHEN EXHAUST FAN TO BE 100 CFM MIN. AND SHALL VENT <br />TO OUTSIDE. <br />ALL EXHAUST DUCTS SHALL BE RIGID METAL, AND SHALL BE <br />FITTED WITH A TIGHT FITTING BACGGAFT DAMPER CAPABLE OF <br />CLOSING WHEN THE FAN IS NOT IN USE. <br />DUCTS IN UNHEATED SPACES INCLUDING ATTICS SHALL BE <br />INSULATED TO A MINIMUM OF R-4. <br />TOP FLOOR EXHAUST FANS SHALL VENT THROUGH ROOF. <br />MECHANICAL VENTILATING SYSTEMS IN BATHROOMS AND <br />LAUNDRY ROOMS SHALL EXHAUST DIRECTLY TO THE OUTSIDE. <br />DUCTS PENETRATING OCCUPANCY SEPARATION BETWEEN <br />GARAGE AND DWELLING, AND WITHIN THE GARAGE SHALL BE <br />CONSTRUCTED OF NO. 26 GAUGE SHEET STEEL. <br />DRYER EXHAUST DUCT SHALL BE 4" RIGID METAL WITH A 4" <br />OPENING ON THE EXHAUST HOOD. THE DRYERS SHALL BE <br />GENERAL. ELECTRIC. DRYER SHALL BE INSTALLED ACCORDING <br />TO MANUFACTURER'S INSTALLATION INSTRUCTIONS ON SITE. <br />5052 REGISTERED <br />ARCHITECT <br />ROBERT E. WEIBLE <br />STATE OF WASHINGTON <br />as <br />L <br />_N <br />-Q <br />c <br />a. <br />o <br />•N <br />U <br />a� <br />L <br />r <br />L <br />L <br />C <br />T <br />wQ <br />C\ <br />w` <br />W <br />�L <br />0 <br />V <br />O <br />Q <br />"T7 <br />o <br />to <br />� <br />O <br />a <br />a <br />tt1 <br />� <br />O <br />r <br />a <br />0 <br />O <br />e� <br />M <br />O <br />e� <br />u <br />■ <br />L <br />0 <br />0 <br />n <br />r <br />0 <br />1 <br />Lf) <br />> <br />0 <br />E <br />:s <br />W <br />IL <br />A <br />r <br />._ <br />0 <br />a. <br />o Job No.: 14-38 <br />U <br />Sheet No.: <br />0 <br />N <br />