528 MADISON ST 2025-09-26 - Laserfiche WebLink

INTERIOR EXTERIOR R-10 FOAM @ HEADER TYP TYP EXTERIOR WALL A55EMBLY FOLD UP WEATHER HEADER PER STRUCTURAL SELF-ADHESNE RESISTIVE BARRIER OR EXI5T WATERPROOF MEMBRANE AND TEMPORARILY INSTALL PER 4/A5.0 WEATHER RESISTIVE SECURE 1/2"GWB BARRIER MTL FLASHING OVER WD TRIM WD TRIM PER TYP DETAIL �'�� EXTERIOR SHEATHING 6/A5.0 WD TRIM PER TYP DETAIL TAPE WEATHER RESISTIVE SILL PLATE WINDOW LINER 5/A5.0 WINDOW PER WINDOW BARRIER SCHEDULE Grd G x INSTALLED J TYP WINDOW HEAD WINDOW b W 1 _,,-0„ 0 TYP EXTERIOR WALL SILL TAPE O ASSEMBLY i (WATERPROOF, C AIRTIGHT TAPE) C M WD TRIM PER TYP WATERPROOF W CD DETAIL 5/A5.0 AIRTIGHT TAPE (n CO Z 0-)j O SELF-ADHESIVE WATERPROOF MEMBRANE INSTALL PER 4/5.0 WINDOW FLASHING 6.INSTALL FLANGED WINDOW AND FASTEN TO O Q 1.CUT THE WRB FLUSH WITH THE ROUGH OPENING TRIM PER TYP DETAIL 2.CUT THE WRB AT 45 DEGREE ANGLE TO A POINT STRUCTURE PER NG INSTRUCTIONS. W E 6/ 7 A5.0 9"UP AND 9"OUT FROM THE UPPER CORNERS OF .WRB AT TOP FLANGE:UNFOLD WRB AND RUN IT = 00 1/2"GWB THE ROUGH OPENING OVER THE TOP OF FLANGE. N W 3.FOLD UP WRB FLAP A7 HEAD AND TEMPORARILY 8.FLANGE TAPE:USE FLANGE TAPE TO SEAL Z Lo > SECURE WITH MASKING TAPE 50 THAT IT CAN BE BOTTOM FLANGE TO THE WRB.PRESS FIRMLY TO O W TYP WINDOW JAMB INSTALLED OVER THE HEADER FLANGE OF THE AFFIX. 7 WINDOW LATER. 9.TAPE THE 51PE FLANGES TO THE WRB. co 4.IN 5 O THE ROUGH OPENING AND SECURE FOLD BACK THE OTHER TWO EDGES THE WRB 10.TAPE THE WRB TO THE TOP FLANGE INTO 11,TAPE THE DIAGONAL CUTS IN THE WRB ABOVE Q SILL PER TYP DETAIL STAPLING.TO ENSURE POSITIVE DRAINAGE THE WINDOW HEAD.E OF THE Q SILL/PREVENT WATER INTRUSION,ADD A BACK DAM •NOTE:MAKE SURE TAPING IS DONE FROM BOTTOM OR SLOPE SILL AT THE BOTTOM OF THE R.O. TO TOP 50 THAT ALL TAPE JOINTS ARE PROPERLY 5.INSTALL SILL TAPE ON WINDOW SILL,EXTENDING 5HIFLAPPED. 2x WD SILL W/SLOPE&DRIP IT UP EACH SIDE A MIN OF 4".ACCURATELY PRE55 INTO CORNERS.OVERLAP THE VERTICAL FACE OF SELF-ADHESIVE WATERPROOF THE WRB APPROXIMATELY MIN 1".TRIM AND MEMBRANE,INSTALL PER 4/A5.0 PRE55/5TREGH AROUND BOTH CORNERS. TYP EXTERIOR 4iWALL ASSEMBLY INTERIOR EXTERIOR TYP WINDOW SILL TYP WINDOW FLASHING DTL 3 V -0, `'F N.T.S. OR APPROVED EQUAL 9716 REGISTERED TYPICAL WINDOW NOTE: ARCHITECT 1.INSTALL BACKER ROD AND/OR FOAM INSULATION Cap ANY GAP BETWEEN WINDOW AND ROUGH FRAME,TYP ° � — HEIDI MICHELLE HELGESON STATE OF WASHINGTON 10 WD TRIM, GWB,UNO 20 WD TRIM W/ ix3 WD TRIM, W/MITERED MITERED CORNER W/MITERED CORNERS CORNERS 20 WD TRIM W/ WD TRIM PER TYP MITERED CORNER DETAIL 8/A5.0 DOOR PER SCHEDULE TYP WALL A55EMBLY WINDOW PER WINDOW LN WINDOW PER WINDOW 5CHEDULE 1/2"x2 WOOD BASE, SCHEDULE LINE OF DOOR LINE OF DOOR DOOR JAMB PAINTED TO MATCH 51LL PER TYP DETAIL JAMB,TYP JAMB,TYP DOOR FRAME WD TRIM PER TYPO TYP. 2x_WOOD SILL,WITH DETAIL 8/A5.0 SLOPE AND DRIP,SET DOOR PER DOOR DOOR PER SCHEDULE GWB,UNO PROUD OF FACE OF SIDE DOOR PER DOOR SCHEDULE FINISH FLOORING TRIM TYP SCHEDULE TYP EXT.WNDW TRIM TYP INT.WNDW TRIM TYP EXT. DOOR TRIM �TYPDOOR TRIM TYP INT DOOR HEAD TYP INT DOOR JAMB TYP WD BASE DTL 7 9 10 11 3/4"_,_Q„ `VERIFY MATCH EXISTING EX15TING SIDING,PATCH TO MATCH EXISTING FINISH FLOOR 9 AREA OF ALTERATION EXISTING WRB,PATCH TO MATCH PLYWOOD SHEATHING PER STRUCTURAL HZ D EXISTING @ AREA OF ALTERATION 2X PT SLEEPERS PER STRUCTURAL A R C H I T E C T U R E EXISTING 5HEATHNG,PATCH TO F RIPPED AS REQ'D TO PROVIDE LEVEL FLOOR MATCH EXISTING 0 AREA OF FILL WITH RIGID INSULATION D E S I G N ALTERATION EXISTING 2X4 STUD WALL,INFILL TO FLOAT OVER EXISTING SLAB ON GRADE MATCH EXISTING @ AREA OF ALTERATION 23020 EDMONDS WAV, #113 FILL ANY EXPOSED EXISTING 2X4 BAYS W/R-15 HIGH DENSITY EDMONDS,WA 98020 BATT INSULATION,TYP. P.2 0 6. 5 4 2 . 3 7 3 4 EX157ING GWB OR 1/2"GWB VERIFY www.h2dar c h 1 tects.c om FLUSH W/EXISTING FINISH,FVA 12 INT TYP EXT W A ALL ASSEMBLY TYP FLOOR ASSEMBLY DATE: 12/22I2023 PERMIT SET TYP.DETAILS A5.0