|
1 2 3 4 5
<br /> V £
<br /> ELECTRICAL SPECIFICATIONS 6
<br /> ➢�o
<br /> SECTION 260100-GENERAL PROVISIONS SECTION 260510-EXISTING SYSTEMS NO
<br /> �-
<br /> 0.ACCESS TO PERFORM WORK o 8 5
<br /> on
<br /> PROVIDE COMPLETE AND FULLY OPERATIONAL ALL ELECTRICAL SYSTEMS WITHIN THE PROJECT AREA,ALONG A.EXISTING SYSTEMS AND SYSTEMS ADJACENT TO THE WORK SHALL BE INVESTIGATED THOROUGHLY. ANY CAREFULLY REMOVE, STORE OR TEMPORARILY HANG AND RE-INSTALL IN UNDAMAGED CONDITION ALL to V -o
<br /> WITH POWER CONNECTIONS TO EQUIPMENT FURNISHED UNDER OTHER DIVISIONS OF THE SPECIFICATIONS. DAMAGE RESULTING FROM PERFORMANCE OF WORK UNDER THIS CONTRACT SHALL BE REPAIRED TO ASSURE ELECTRICAL EQUIPMENT,LIGHTING FIXTURES,AND CEILING TILES WHERE ACCESS TO PERFORM WORK IS a a&
<br /> CONTINUING OPERATION AND INTEGRITY DURING AND AT COMPLETION OF THE PROJECT AT NO INCREASE IN REQUIRED.CLEAN PRIOR TO RE-INSTALLATION. 40 o a t
<br /> A.CODES CONTRACT COST.ANY EXISTING WIRING SERVING DEVICES REMAINING IN SERVICE AND INTERRUPTED BY WORK i °g
<br /> PERFORMED UNDER THIS CONTRACT,SHALL BE REROUTED TO MAINTAIN CIRCUIT CONTINUITY. CONTRACTOR tA 6g-°s
<br /> CONFORM TO THE NATIONAL ELECTRICAL CODE AND ALL OTHER CODES AND REGULATIONS AS ADOPTED AND 6
<br /> SHALL ASSUME THE RISK OF MAINTAINING EXISTING SYSTEMS,EXCEPT RELOCATION OF WIRING OF#2 AWG AND
<br /> ACT(DAD BY THE STATE OF WASHINGTON AND CITY OF EVERETT INCLUDING THE AMERICANS WITH DISABILITIES ABOVE SHALL BE CONSIDERED AN ADDITIONAL COST IF NOT SHOWN TO BE RELOCATED. IF SUCH WIRING IS SECTION 260519-LOW VOLTAGE ELECTRICAL POWER CONDUCTORS AND CABLES o 0€:9£
<br /> ( ) FOUND THE CONTRACTOR SHALL NOTIFY ENGINEER OF WIRING LOCATION,REASON IT MUST BE REMOVED AND N q F -
<br /> e
<br /> D COST OF RELOCATION AND RECEIVE THE OWNER'S APPROVAL BEFORE PROCEEDING WITH THE WORK. THE A.PROVIDE ALL WIRE AND CABLE COMPLETE. a F vi
<br /> B.PERMITS AND FEE BUILDING WILL CONTINUE OPERATION DURING THE WORK AND IT IS ESSENTIAL THAT NO SYSTEMS OPERATION COPPER,INSULATED FOR 600V.ALUMINUM OR COPPER CLAD ALUMINUM CONDUCTORS NOT PERMITTED.TYPE
<br /> CONTRACTOR TO OBTAIN AND PAY FOR ALL REQUIRED LICENSES,PERMITS AND INSPECTIONS. BE INTERRUPTED UNLESS SCHEDULED WITH THE OWNER. CONTRACTOR SHALL ASSUME RESPONSIBILITY FOR °'a
<br /> THW,THWN/THHN OR XHHW-2.NUMBER 12 AWG MINIMUM FOR POWER AND LIGHTING CIRCUITS.
<br /> UNSCHEDULED INTERRUPTIONS AND EXPEDIENT REPAIR. G
<br /> C.COORDINATION B.CONDUCTOR INSULATION:
<br /> CONTRACTOR TO COORDINATE ELECTRICAL WORK WITH OTHER TRADES. B.EXISTING SYSTEMS CONCEALED COMPLY WITH NEMA WC 70/ICEA S-95-658 FOR TYPE THHN-THWN.
<br /> 1. THE ELECTRICAL DRAWINGS SHOW PORTIONS OF THE EXISTING ELECTRICAL SYSTEMS WHICH ARE TO
<br /> D.WARRANTY REMAIN,BE REMOVED OR BE MODIFIED AS A PART OF THE CONTRACTOR'S WORK.CONCEALED FEATURES C.SPLICES
<br /> PROVIDE WARRANTY FOR ONE FULL YEAR AFTER COMPLETION. OF THE EXISTING SYSTEMS ARE DERIVED FROM RECORD DRAWINGS AND THE ENGINEER'S BEST SOLDERLESS TYPE ONLY. PRE-INSULATED TWIST-ON'TYPE(LIMITED TO SIZE#10 AND SMALLER). BOLT OR
<br /> JUDGMENT OF THE CONFIGURATION,BUT NO GUARANTEE IS MADE AS TO THEIR CORRECTNESS. COMPRESSION SET TYPE WITH APPLICATION OF PREFORMED INSULATED COVER,HEAT SHRINKABLE TUBING OR
<br /> E.CONTRACT DRAWINGS 2. THE CONTRACTOR SHALL INSPECT THE EXISTING INSTALLATION PRIOR TO BIDDING AND SHALL MAKE PLASTIC INSULATED TAPE ACCEPTABLE FOR ALL SIZES.
<br /> RACEWAYS AND OUTLET BOXES ARE SHOWN DIAGRAMMATICALLY ONLY AND THE LAYOUT DOES NOT THEIR OWN JUDGMENT AS TO THE WORK REQUIRED TO PROVIDE A COMPLETE INSTALLATION AND
<br /> NECESSARILY SHOW THE TOTAL NUMBER OF RACEWAYS NOR THEIR EXACT LOCATION.THE CONTRACTOR SHALL DEMOLITION WITHIN THE INTENT OF THE CONTRACT DOCUMENTS. D.TERMINATIONS
<br /> PROVIDE ALL RACEWAYS,BOXES,CABLES,AND OTHER MATERIALS REQUIRED FOR THE COMPLETE ELECTRICAL COMPRESSION SET,BOLTED OR SCREW TERMINAL. CONDUCTORS#12 AND SMALLER SHALL UTILIZE EYE OR
<br /> SYSTEMS SHOWN OR INDICATED ON THE CONTRACT DRAWINGS. C.EXISTING SYSTEM DRAWINGS FORKED TONGUE TYPE COMPRESSION SET TERMINATOR WHEN TERMINATION IS TO A BOLTED SCREW SET TYPE �j
<br /> THE DRAWINGS SHOW PORTIONS OF THE EXISTING SYSTEMS WHICH ARE DERIVED FROM RECORD DRAWINGS. TERMINAL BLOCK OR TERMINAL CABINET.
<br /> F.RECORD DRAWINGS THE DRAWINGS ARE INCOMPLETE AND NO GUARANTEE IS MADE TO THEIR CORRECTNESS.THE CONTRACTOR I o
<br /> E
<br /> AT THE CONCLUSION OF CONTACT WORK,PROVIDE THE OWNER WITH A COMPLETE SET OF REPRODUCIBLE SHALL ASSUME THERE IS 20%MORE ELECTRICAL SYSTEMS THAN SHOWN ON THE DEMOLITION AND EXISTING E.COLOR CODE
<br /> DRAWINGS WITH ALL CHANGES CLEARLY AND LEGIBLY MARKED TO REFLECT THE AS-BUILT CONDITIONS.THESE SYSTEM DRAWINGS. 460 MARKING BRN,ORG,YELL,GRAY NEUTRAL
<br /> DRAWINGS SHALL BE LABELED"AS-BUILT'AND CERTIFIED BY THE CONTRACTOR FOR ACCURACY. D.DEMOLITION WORK 208 MARKING BILK,RED,BLU,WHITE NEUTRAL
<br /> G.MAINTENANCE MANUALS CONTRACTOR SHALL REMOVE ALL ELECTRICAL EQUIPMENT IN THE AREA BEING REMODELED WHICH IS NO F.BRANCH CIRCUITS I a
<br /> LONGER IN SERVICE PRESENTLY OR AS A RESULT OF THIS CONTRACT. THE DEFINITION OF ELECTRICAL
<br /> COMPLETE FOR EVERY SYSTEM.PROVIDE MANUAL TO OWNER IN ELECTRONIC MEDIUM. EQUIPMENT IS ANY EQUIPMENT MENTIONED IN THE NATIONAL ELECTRICAL CODE. COPPER.SOLID FOR NO.10 AWG AND SMALLER;STRANDED FOR NO.8 AWG AND LARGER.
<br /> H.QUALITY ASSURANCE E.PREMIUM TIME G.ALL 480/277V WIRING WILL BE SEPARATED FROM THE 208/120V WIRING AT ALL TIMES.EXCEPTIONS:MOTOR
<br /> 1. MATERIALS AND SYSTEMS:PROVIDE UL LISTED AND LABELED MATERIALS WHERE LISTING SERVICE IS PREMIUM TIME SHALL BE INCLUDED IN THE BASE BID FOR ELECTRICAL SYSTEM(S)OUTAGES AND FOR OTHER CONTROLS
<br /> NORMALLY PROVIDED FOR A GIVEN PRODUCT.PROVIDE NEW AND SHIP TO JOBSITE IN ORIGINAL WORK AS REQUIRED BY THE SCHEDULE,AS SHOWN ON THE DRAWINGS AND AS NOTED IN OTHER DIVISIONS OF
<br /> MANUFACTURER'S CONTAINERS OR BUNDLES. THE SPECIFICATIONS. H.CORD DROPS AND PORTABLE APPLIANCE CONNECTIONS:TYPE SO,HARD SERVICE CORD WITH
<br /> 2. WORKMANSHIP:ARRANGE WORK TO OBTAIN COORDINATED INSTALLATION. STAINLESS-STEEL,WIRE-MESH,STRAIN RELIEF DEVICE ATTERMINATIONS TO SUIT APPLICATION.
<br /> 3. ROUTING:EXACT ROUTING OF WIRING AND LOCATIONS OF OUTLETS,PANELS,ETC.SHALL BE GOVERNED F.WORK OUTSIDE OF REMODEL AREAS
<br /> BY STRUCTURAL CONDITIONS,OBSTRUCTIONS,AND EXISTING CONDITIONS.ARCHITECT RESERVES THE CAUTION-THIS WORK IS NOT SHOWN ON THE CONTRACT DOCUMENTS. PROVIDE NEW WIRING SYSTEMS IN
<br /> O RIGHT AT NO INCREASE IN PRICE,TO MAKE REASONABLE CHANGES IN LOCATIONS OF ELECTRICAL ITEMS CONCEALED CEILING SPACES TO SWITCHBOARDS, PANELBOARDS, COMMUNICATION AND SIGNALING AND SECTION 260526-GROUNDING o
<br /> EXPOSED AT CEILING AND/OR ON WALLS. SYSTEM CONTROL PANELS.PROVIDE NEW CONDUIT SYSTEMS IN CEILING SPACES OF FLOOR BELOW REMODEL
<br /> FLOORS. REMOVE AND RELOCATE ELECTRICAL EQUIPMENT IN THE WAY OF OTHER TRADES WORK INSTALLED A.PROVIDE A GROUNDING SYSTEM FOR EQUIPMENT AND DEVICE GROUND AS REQUIRED BY CODE.
<br /> I.COORDINATION UNDER THIS CONTRACT.SPACES ABOVE EXISTING CEILINGS ARE HIGHLY CONGESTED.ROUTE WIRING AROUND
<br /> 1. WORK OUT ALL"TIGHT"CONDITIONS INVOLVING WORK UNDER THIS CONTRACT IN ADVANCE OF OBSTRUCTIONS AND PROVIDE PULL BOXES PER CODE. B. GROUNDING BUS:
<br /> INSTALLATION.
<br /> 2. COORDINATE ALL ELECTRICAL POWER AND CONTROL WIRING REQUIREMENTS OF MECHANICAL 1. INSTALL BUS ON INSULATED SPACERS 2 INCHES MINIMUM FROM WALL,6 INCHES ABOVE FIN-ISHED FLOOR g
<br /> G.EXISTING MATERIALS UNLESS OTHERWISE INDICATED.
<br /> EQUIPMENT. R
<br /> ALL MATERIALS WHICH AREA PART OF THE BUILDING SHALL REMAIN THE PROPERTY OF THE OWNER. 2. PREDRILLED RECTANGULAR BARS OF ANNEALED COPPER,114 BY 4 INCHES IN CROSS SECTION,WITH
<br /> 3. CONFIRM ALL ELECTRICAL EQUIPMENT SYSTEM PROGRAMMING NOMENCLATURE REQUIREMENTS 9/32-INCH HOLES SPACED 1-1/8 INCHES APART.STAND-OFF INSULATORS FOR MOUNTING SHALL COMPLY z I a
<br /> WITH THE OWNER PRIOR TOO SUBMITTALS
<br /> TALS AND ROUGH-IN.CONFORM TO ALL NAMING CONVENTIONS H.EXISTING MATERIALS TO BE REINSTALLED WITH UL 891 FOR USE IN SWITCHBOARDS,600 V.LEXAN OR PVC,IMPULSE TESTED AT 5000 V.
<br /> DEFINED THROUGHOUT THE PROJECT. EXISTING MATERIALS AND EQUIPMENT(EXCEPT INTERIOR,UNDAMAGED RACEWAYS)THAT ARE REMOVED AS A
<br /> PART OF THE WORK OR STORED IN SURPLUS SHALL NOT BE REINSTALLED AS A PART OF THE NEW SYSTEMS
<br /> UNLESS SPECIFICALLY NOTED OR AUTHORIZED IN WRITING BY THE OWNER. FORWARD A COPY OF THE SECTION 260533-RACEWAYS AND BOXES m
<br /> SECTION 260126-TESTING AUTHORIZATION TO THE ENGINEER. THE REQUIREMENTS OF THE SPECIFICATIONS (I.E., CONDITION,
<br /> INSTALLATION,TESTING,ETC.)SHALL APPLY AS IF THE MATERIALS WERE NEW,FURNISHED BY THE CONTRACTOR. A.PROVIDE RACEWAY SYSTEM COMPLETE AND IN CONFORMANCE WITH CODE.INSTALL RACEWAYS CONCEALED
<br /> A.FURNISH ALL LABOR AND TEST EQUIPMENT AS REQUIRED UNDER THIS SECTION. IN CONSTRUCTION FOR ALL AREAS UNLESS EXPOSED RACEWAYS ARE SPECIFICALLY SHOWN.
<br /> I.EXISTING MATERIALS NOT TO BE REINSTALLED
<br /> 0
<br /> B.FACILITIES ENGINEERING REPRESENTATIVE NEEDS TO BE PRESENT FOR FINAL TESTING. ALL MATERIAL TO BE DEMOLISHED AND DEBRIS SHALL BE LEGALLY DISPOSED OF BY THE CONTRACTOR. B.PROVIDE 1"RACEWAY FOR HOMERUNS AND MAJOR CEILING CONDUIT RUNS.RACEWAY DROPS DOWN WALLS I
<br /> 0
<br /> C.TEST ALL PANELS AND/OR BRANCH CIRCUITS FOR GROUNDS OR SHORTS. REPAIR DEFECTIVE WIRING AS J.EXISTING RACEWAYS AND RACEWAY CARRYING 2 CURRENT CARRYING CONDUCTORS CAN BE 3/4".MINIMUM RACEWAY SIZE IS 3/4".
<br /> REQUIRED.TEST EACH INDIVIDUAL CIRCUIT AT PANEL FOR PROPER OPERATION. 1. THE CONTRACTOR MAY REUSE THE EXISTING RACEWAYS IF NO OTHER SYSTEMS OCCUPY THE RACEWAY, C.PROVIDE PULLWIRE IN ALL EMPTY RACEWAYS. o
<br /> RACEWAYS AND ENCLOSURES ARE ELECTRICALLY AND MECHANICALLY CONTINUOUS AND NEW WIRING IS u
<br /> D.AT COMPLETION OF WORK,PROVIDE WRITTEN CERTIFICATION THAT ALL SYSTEMS ARE FUNCTIONING PROVIDED.NO WARRANTY IS MADE AND THE CONTRACTOR SHALL ASSUME THE RISK OF USING EXISTING D.INTERIOR RACEWAYS
<br /> PROPERLY WITHOUT DEFECTS. OUTLET BOXES AND RACEWAY SYSTEMS.
<br /> 2. THE CONTRACTOR SHALL RELOCATE EXISTING RACEWAYS IN THE AREA OF WORK AS REQUIRED TO ELECTRICAL METALLIC TUBING(EMT)WITH STEEL COMPRESSION OR SET SCREW FITTINGS.INDENTOR,DRIVE-ON, Permit/Seal
<br /> SUPPORT INSTALLATION OF MECHANICAL EQUIPMENT.IT IS THE RESPONSIBILITY OF THE ELECTRICAL AND PRESSURE CAST ON DIE CAST TYPE SET SCREW FITTINGS ARE NOT ACCEPTABLE.
<br /> SECTION 260500-BASIC MATERIALS AND METHODS CONTRACTOR TO COORDINATE WITH MECHANICAL CONTRACTOR TO DETERMINE THE EXTENT OF
<br /> EXISTING CONDUITS THAT NEED TO BE RELOCATED E.RACEWAY PENETRATIONS L A N
<br /> ti Was
<br /> INCLUDES GENERAL REQUIREMENTS FOR MATERIALS AND INSTALLATION METHODS, CUTTING BUILDING �
<br /> PENETRATIONS THROUGH FIRE RATED CONSTRUCTION SHALL BE SEALED USING 3M FIRE BARRIER CAULK, lV of y7 '�
<br /> CONSTRUCTION,PAINTING,CLEAN-UP,AND WORKMANSHIP. K.EXISTING CONDITIONS NELSON ELECTRIC FLAMESEAL,OR T&B FLAMESAFE.
<br /> EXAMINE THE STRUCTURE,BUILDING,AND CONDITIONS UNDER WHICH ELECTRICAL WORK IS TO BE INSTALLED
<br /> B A.MATERIALS FOR CONDITIONS DETRIMENTAL TO PROPER AND TIMELY COMPLETION OF ELECTRICAL WORK.DO NOT PROCEED F. PROVIDE AND SIZE OUTLET BOXES FOR DEVICES SUCH AS RECEPTACLES,SWITCHES,AND LIGHT FIXTURES
<br /> WITH WORK UNTIL DEFICIENCIES OR DETRIMENTAL CONDITIONS HAVE BEEN CORRECTED. REPORT AND PULL BOXES AS REQUIRED IN THE CONDUIT SYSTEM PER THE NATIONAL ELECTRICAL CODE.CONTRACTOR
<br /> 341
<br /> ALL MATERIALS SHALL BE NEW,FREE FROM DEFECTS,AND SHALL HAVE BEEN TESTED AND LISTED BY DEFICIENCIES OR DETRIMENTAL CONDITIONS OF EXISTING ELECTRICAL WORK WHICH MIGHT BE UNSUITABLE TO SHALL COORDINATE WITH GENERAL CONTRACTOR TO DETERMINE ANY SPECIALTY INSTALLATION A90,i. 2GIs-f
<br /> UNDERWRITERS LABORATORIES,OR OTHER APPROVED TESTING ORGANIZATION,AND SHALL BE SO LABELED. CONNECT WITH OR RECEIVE OTHER WORK. FAILURE TO SO REPORT SHALL CONSTITUTE ACCEPTANCE OF REQUIREMENTS DUE TO FIRE RATINGS,CORE WALLS,ETC. '°s 101VAL EIyG�
<br /> OTHER WORK AS BEING FIT AND PROPER FOR THE RECEPTION OF ELECTRICAL WORK. 04/01/2025
<br /> B.SUBSTITUTIONS G.INTERIOR WIRING:RESSED STEEL,ZINC COATED WITH PLASTER RING WHERE APPLICABLE. MOUNT OUTLET
<br /> SHALL BE REVIEWED BY THE ENGINEER. L.EXISTING SYSTEMS MAINTAINED BOXES FOR RECEPTACLES AND OTHER DEVICES AT 18",UNLESS OTHERWISE NOTED.
<br /> GENERAL
<br /> C.WORKMANSHIP REROUTE EXISTING CIRCUITS THAT ARE INTERRUPTED AS A RESULT OF THIS CONTRACT THAT SERVE DEVICES
<br /> SHALL BE OF THE BEST QUALITY AND PERFORMED BY EXPERIENCED ELECTRICIANS UNDER SUPERVISION OF AN TO REMAIN IN SERVICE. SECTION 262726-WIRING DEVICES
<br /> EXPERIENCED FOREMAN. 1.POWER CIRCUITS
<br /> TRACE OUT AND IDENTIFY LOADS AND SYSTEMS BEING SERVED. A.RECEPTACLES
<br /> D.NOISE TRANSMISSION PROVIDE TEMPORARY WIRING,SCHEDULE OUTAGE AND RECONNECT LOADS TO TEMPORARY WIRING.
<br /> TO PREVENT NOISE TRANSMISSION(IN NEW CONSTRUCTION)BETWEEN ADJOINING ROOMS,ALL DEVICES ON PROVIDE NEW WIRING IN NEW LOCATION. PROVIDE 15 AMP RECEPTACLES IN ALL LOCATIONS EXCEPT PROVIDE 20 AMP RECEPTACLES ON DEDICATED 20 J
<br /> OPPOSITE SIDES OF WALL TO BE SPACE A MINIMUM OF 6"APART(HORIZONTALLY PREFERRED). AMP CIRCUITS. N
<br /> SCHEDULE OUTAGE,DISCONNECT TEMPORARY WIRING,AND CONNECT LOADS TO NEW WIRING. U EL J
<br /> E.BRANCH CIRCUITING B. IDENTIFICATION :2U
<br /> M.DEMOLITION E-)w Q Q
<br /> NO MORE THAN SIX CURRENT CARRYING CONDUCTORS IN ANY ONE(1)HOMERUN. ELECTRICAL EQUIPMENT FREE STANDING OR SURFACE MOUNTED,RACEWAY(EXPOSED)AND CONDUCTORS; RECEPTACLE DEVICE PLATES SHALL BE LABELED BELOW WITH PANELBOARDS AND CIRCUIT NUMBER(BLACK V
<br /> WHICH ARE NO LONGER IN SERVICE PRESENTLY OR AS A RESULT OF THIS CONTRACT SHALL BE REMOVED. FILLED LETTERS).RECEPTACLE COVERPLATES FOR RECEPTACLES OTHER THAN 15 AND 20 AMP SHALL BE LLI
<br /> F.GROUNDING UNUSED FLUSH MOUNTED DEVICES,OUTLET AND OTHER BOXES IN FINISHED AREAS SHALL BE REMOVED FROM LABELED WITH AMPERE RATING,VOLTAGE AND PHASE.UTILIZE MACHINE PRINTED ADHESIVE FILM LABELS BY Q J w
<br /> a PROVIDE SEPARATE GREEN GROUNDING CONDUCTOR IN ALL EQUIPMENT AND RECEPTACLE BRANCH CIRCUITS. WALL AND THE REMAINING HOLE PATCHED TO MATCH ADJACENT WALL SURFACES. UNUSED RACEWAYS AND THERMAL TRANSFER OR EQUIVALENT PROCESS. Z O
<br /> SIZE PER NEC. SLEEVES EMBEDDED IN CONCRETE SHALL BE CUT FLUSH AT CEILING,FLOOR OR WALL AND FILLED WITH GROUT. O L) Q
<br /> ALL UNUSED RACEWAYS ABOVE CEILINGS SHALL BE REMOVED.CONTRACTOR SHALL REMOVE ALL FLOOR,WALL (D w w
<br /> G.CUTTING AND PATCHING OR CEILING MOUNTED ELECTRICAL EQUIPMENT IN THE"DEMOLITION AREA"INDICATED ON THE DRAWINGS EVEN Luaof w Q w
<br /> IF THE EQUIPMENTIOR DEVICE IS NOT SHOWN ON THE PROJECT DRAWINGS. IF CONTRACTOR QUESTIONS D
<br /> DO NOT CUT STRUCTURAL MEMBERS. ALL CONSTRUCTION MATERIALS DAMAGED OR CUT INTO DURING THE w uf j
<br /> INSTALLATION OF THIS WORK MUST BE REPAIRED OR REPLACED WITH MATERIALS BY SKILLED LABOR WHETHER A PARTICULAR DEVICE IS TO BE REMOVED,NOTIFY THE ENGINEER NOTING TYPE AND LOCATION OF _ (� w (,) Q
<br /> DEVICE. IF SO DIRECTED THE CONTRACTOR SHALL MAINTAIN THE EXISTING DEVICE IN SERVICE WITHOUT ANY a Z > r
<br /> EXPERIENCED IN THAT PARTICULAR BUILDING TRADE. CHANGE IN CONTRACT PRICE. a w w m
<br /> o Q of
<br /> � H.PAINTING 1 Lu Z OV
<br /> N.POWER OUTAGES Z
<br /> `c 3
<br /> TOUCH-UP TO MATCH FACTORY PAINT ANY ELECTRICAL ITEMS SCRATCHED OR MARRED IN SHIPMENT OR N
<br /> INSTALLATION. 1. SCHEDULED OUTAGES.THE EXISTING FACILITY WILL CONTINUE ITS NORMAL OPERATION DURING THE V LU �,
<br /> CONSTRUCTION WORK;THEREFORE IT IS REQUIRED THATTHE CONTRACTOR SCHEDULE ELECTRICAL
<br /> m
<br /> A I.CLEAN UP SYSTEM(S)OUTAGES WITH THE OWNER.SUBMIT A WRITTEN REQUEST FOR A POWER OUTAGE AT LEAST Project No.:204823068
<br /> ONE WEEK IN ADVANCE IDENTIFYING THE AREAS,AND SYSTEMS THAT WILL BE AFFECTED,TIME AND
<br /> CONTINUALLY REMOVE DEBRIS,CUTTINGS,CRATES,CARTONS,ETC. CAREFULLY CLEAN WIRING DEVICES, DURATION OF THE POWER OUTAGE.THE CONTRACTOR SHALL RECEIVE WRITTEN AUTHORIZATION TO
<br /> COVER PLATES,LIGHT FIXTURES,ETC.,TO REMOVE PAINT AND PLASTER,ETC. PROCEED WITH THE OUTAGE AND SHALL RE-NOTIFY THE OWNER VERBALLY AT LEAST ONE HOUR PRIOR Scale:NONE
<br /> a TO THE OUTAGE AND ALSO NOTIFY THE OWNER WHEN THE OUTAGE IS COMPLETED. MEH MEH NCA 2025.04.01
<br /> 2. UNSCHEDULED OUTAGES.IN THE EVENT THAT THE CONTRACTOR'S WORK CAUSES OR CONTRIBUTES TO
<br /> AN UNSCHEDULED SYSTEM(S)OUTAGE(OR OTHER SYSTEM FAULT),THE CONTRACTOR IS RESPONSIBLE own. osOn. cnkd. vvrv.MM.00
<br /> FOR IMMEDIATELY CORRECTING THE PROBLEM.INCLUDED(AS EXAMPLES)SHALL BE ANY PREMIUM TIME Title
<br /> REQUIRED TO STAY ON THE JOB SITE UNTIL PROBLEM IS CORRECTED AND AIR FREIGHT FOR PARTS NOT ELECTRICAL
<br /> LOCALLY AVAILABLE.
<br /> SPECIFICATIONS
<br /> 0
<br /> EVE`TT Reviewed for Permit 04 09 2025 Drawing NO.
<br /> g E0.1
<br /> V ORIGIHALSHEF IRCHD
<br />
|