Laserfiche WebLink
9 Y PREMIUM <br /> l 1 <br /> HYBRID <br /> CROSSOVER <br /> COMPLIANCE: Exceeds performance requirements of ASTM D4869, D226, <br /> D1970'.Florida Building Code Approved.Miami-Dade County Product Control <br /> Approved.UL Classified File#R14831. <br /> NOTE:Read entire label before installing this product. <br /> DESCRIPTION:CrossOverT°"CX-L Premium Hybrid Roof Undedayment is <br /> your high quality roofing underlayment designed to shed water off your roof «N, <br /> and away from your home or building. This Hybrid product uses advanced <br /> technology, combining the best properties of traditional organic felts and '` /' ►,� <br /> synthetic products.This CrossOverTM CX-L advanced design creates a superior EroQ&o L* r` <br /> roof underlayment with faster and easier installation, as well as improvedNh <br /> performance and durability. { <br /> Roof underlayments perform a vital role in protecting your home or building c{ <br /> against damage from wind,moisture,rain,UV and other destructive elements. <br /> Unfortunately,most do not stand up to the test of time.Whether it is wind,water <br /> or UV damage, CrossCiverTM CX-L provides the most advanced protection in s <br /> its class.Rest assured,you are protected from the elements with CrossOverTM <br /> CX-L Premium Hybrid Roof Technology. <br /> •Higher strength&wrinkle free,even when soaking wet! <br /> •Extra tough&durable construction! <br /> •Withstands extreme cold&blazing desert heat! <br /> •Use in high wind areas where other products blow off! <br /> •Nail Sealable! <br /> •Limited Lifetime Extended Warranty <br /> EXPOSURE: This product can be left exposed for up to 60 days. Exposure <br /> period is based on standardized testing for UV Resistance only.For high winds, TYPICAL PHYSICAL&PERFORMANCE CHARACTERISTICS: <br /> ensure proper nailing pattern. Size 37.25"x 145' <br /> USES:CrossOverTM CX-L is an excellent underlayment for steep-slope roofing Area 4.5 Squares <br /> such as shingles, wood shake, file, metal, slate and other roof coverings. Permeability ASTM E96 0.05 Perms <br /> CrossOver CX-L acts as a secondary protection barrier. Underlayments will <br /> not prevent wind driven rain from entering the building without sealing laps. Water Transmission ASTM D4869 Pass <br /> CrossOverTM CX-L is not recommended for low slope roofs less than 2:12.Not Tear ASTM D4073 751bf. <br /> recommended or designed as a permanent or primary roof covering. <br /> Breaking Strength ASTM D146 >551bf/in <br /> PREPARATION AND REQUIREMENTS: Always follow focal buildings codes <br /> for you specific region. Ensure the deck is dry, smooth and without voids or Thickness(mm)ASTM D1777 0.60 <br /> unsupported areas.Remove any and all existing nails,fasteners or staples.All Net Mass(g/m2)ASTM D5261 420 <br /> decayed, rotting, rusted or broken materials must be removed and replaced Temperature Range -40•F to 240°F <br /> before installing your roof underlayment. Deck must be in sound condition, <br /> stable and secured to sound framing with the correct fasteners, clips and Pliability,ASTM D146 Pass <br /> spacing as per local building codes and/or shingle or roofing manufacturers Dimensional Stability,ASTM F1087 Pass <br /> published specifications. If using new OSB sheathing or plywood, a gap Cold Flexibility,-25•C,6 hr D5147 Pass <br /> should be left between sheets to allow for expansion and contraction of new <br /> sheathing and prevent bulging and ridges from forming. Spacing should be Unrolling @ 32°F&140°F ASTM D226 Pass <br /> approximately 1/8"at end joints and 3/16"at side joints.Verify with the shingle Nail Sealabilby,ASTM D1970-15 Pass <br /> or other roofing manufacturer's specifications.To help alleviate expansion and <br /> contraction of new OSB or plywood, allow the material to be pre-conditioned <br /> prior to installation.Always use a minimum of 1"long corrosive resistant nails <br /> with a minimum of 3/8" head (ring shank nail leg is recommended). Staples Approx.Shipping Weights:(Note:All approx.weights include container) <br /> should NOT be used. If underlayment is left exposed more than five days, 1" <br /> plastic caps or tin caps must be used.These caps may also be required as per Weight per Roll 40 Ibs <br /> local building codes.Check local codes prior to starting work.Hammer in all Rolls per Pallet 25 <br /> nails at a 90D angle to the roof deck.Nails should be snug and hammered flush Weight of Pallet 1050 Ibs <br /> to the deck with no spaces or gaps.Where you have seams,joints or tears that <br /> require sealant,use APOC approved sealants or tapes. It is recommended to pssrF, <br /> seal laps when there will be exposure to high winds or driving rain.When an ice011 <br /> TDI Listed <br /> barrier is required or for extended warranty, install Weather-Armor SB-1 in all U <br /> valleys and along perimeter edges according to product instructions. <br /> 'Nail sealability <br /> Gardner-Gibson, Inc. • P.O. Box 5449 •Tampa, Florida 33675-5449 <br /> Phone: (813) 248-2101 • Fax(813) 24"768 • www.apoc.com <br /> Page 1 of 2 D-20 <br />