My WebLink
|
Help
|
About
|
Sign Out
Home
Browse
Search
2232 12TH ST 2025-09-30
>
Address Records
>
12TH ST
>
2232
>
2232 12TH ST 2025-09-30
Metadata
Thumbnails
Annotations
Entry Properties
Last modified
9/30/2025 3:43:54 PM
Creation date
9/26/2025 11:20:17 AM
Metadata
Fields
Template:
Address Document
Street Name
12TH ST
Street Number
2232
Imported From Microfiche
No
There are no annotations on this page.
Document management portal powered by Laserfiche WebLink 9 © 1998-2015
Laserfiche.
All rights reserved.
/
38
PDF
Print
Pages to print
Enter page numbers and/or page ranges separated by commas. For example, 1,3,5-12.
After downloading, print the document using a PDF reader (e.g. Adobe Reader).
View images
View plain text
v <br /> POLYFLEX@ <br /> APPLECATIO [NSTR CTIONS <br /> Polyflex G is intended to be used as the primary weathering surface in new or re-roof applications. Polyflex G is to be applied <br /> as the outermost layer of a multi-ply roof system over a compatible Polygloss base or inner ply sheet. Polyflex G may be applied <br /> directly to nor-,combustible substrates. <br /> • Apply over clean, dry, dust and debris-free substrates. Prime concrete decks prior to application with PG 100 <br /> Asphalt Primer. <br /> • When re-roofing, remove all prior roofing materials down to a clean debris-free substrate and properly close-off all <br /> abandoned roof penetrations. <br /> • Concrete or steel decks shall be designed with proper expansion devices. <br /> • Wood decks shall have all joints blocked and properly supported. <br /> • Ensure the fire rating of the assembly over any combustible substrate. <br /> • Ensure the installation of Polyflex G does not prevent the ventilation of existing construction. <br /> • Do not apply over shingles or any granulated surface. <br /> • While installing Polyflex G: <br /> 1. Start at the low point of the roof. <br /> 2. Unroll the material and allow to relax. <br /> 3. Install with traditional torch roofing techniques ensuring proper heating of the roofing material as not to expose <br /> the reinforcement. <br /> 4. Do not heat the substrate. <br /> 5. Position successive rolls providing a minimum 6" end lop and 3" side lop. Asphalt bleed out shall be 1/4" to <br /> 3/8'on all seams. <br /> 6. lops shall be rolled with a 6"-wide railer immediately after heat welding. <br /> • Details and flashing may be installed using Polyflex G with torch applied techniques. Do not use cold adhesives or hot <br /> asphalt. Check project details for proper installation requirements. <br /> POLYGLASS U.S.A., INC. MANUFACTURING FACILITIES <br /> + Fernley, NV <br /> • Hazleton, PA <br /> • Winter Haven, FL <br /> CORPO PIATE HEADQUARTERS <br /> Polygloss U.S.A., Inc. <br /> 1 1 11 West Newport Center Drive <br /> Deerfield Beach, Fl 33442 <br /> www.polyglass.com <br /> General Line:18881410-1375 <br /> 1954)233-1330 <br /> Customer Service; (800)222-9782 <br /> Technical Service: 1,866)802-8017 <br /> Quesfions?technicalopolygloss.com <br /> Product Disclaimer.Unless otherwise incorporoted into or port of o supplemental monufacturer's worronry,Polygloss worronts its productlsl against manufacturing <br /> defects in its product that directly results in leokoge for a period of 5 years. <br /> Refer to material safetydata sheet(MSDS)for specific data and handling of our products.All pt.iERPR00F1AG MATERIALS AND iNSI'LATING SY3T'Eld£ <br /> data furnished refers to standard production and is given in good foith within the applicable i <br /> manufacturing and testing tolerances. <br /> 77 <br /> Polyglass U.S.A.,Inc.,reserves the right to improve and change its products at any time with- <br /> out prior notice. Polyglass U.S.A., Inc. cannot be held responsible for the use of its products <br /> under conditions beyond its own control. <br /> 1-800-222-9782 <br /> For most current product data and warranty information, visit v wv.polyglass.com WWW.polygtass.cont <br />
The URL can be used to link to this page
Your browser does not support the video tag.