3015 9TH ST BLDG 4 2025-11-06 - Laserfiche WebLink

Revision:January 22,2013 Supersedes:November 14,2012 Ref.#:1634630,1652616,1662491, 1672797,1662479(1.5%) DIRECTIONS Tools Typically Required: Utility knife and caulking gun. For best application results, OSIO recommends the use of a high quality caulking gun such as the Albion®612 Cartridge Gun. Safety Precautions: Do not use inside occupied structures. Wear gloves and wash hands after use. Preparation: Apply sealant between 20°F(-7°C)and 100°F(38°C). For easier extrusion of sealant at lower temperatures the material should be kept at room temperature 24 hours prior to use. All surfaces must be clean, dry and free of old caulk, oil, grease, dust, ice, snow, surface water and other contaminants. Insert cartridge into caulking gun,apply moderate pressure in order to break the'Break Away"seal inside the nozzle. Cut the tip off the cartridge at a 45°angle to desired bead size(3/8"is recommended). Application: Using a caulking gun,apply sealant with steady pressure,forcing the sealant into the joint. If the depth of the joint exceeds 3/8"(9.5 mm)the use of a backer rod is recommended. Quad will not pop or splatter and will dispense smoothly on extrusion from the cartridge. Tooling of the sealant is not necessary or recommended. Do not feather or smear sealant. Sealant is paintable when fully cured.Full cure may take 7-14 days or longer depending on ambient conditions and volume of sealant used.Latex paint is recommended.If using oil based/alkyd paint a latex primer should be used first. Clean-up: Clean tools and uncured sealant residue immediately with mineral spirits or paint thinner. Cured sealant must be carefully cut away with a sharp- edged tool. STORAGE -• NOT DAMAGED BY FREEZING. Store in a cool,dry place. Take unwanted product to an approved household hazardous waste transfer facility. Hardened material may be disposed of with trash. DISCLAIMER The information and recommendations contained herein are based on our research and are believed to be accurate, but no warranty,express or implied,is made or should be inferred. Purchasers should test the products to determine acceptable quality and suitability for their own intended use. Nothing contained herein shall be construed to imply the nonexistence of any relevant patents or to constitute a permission,inducement or recommendation to practice any invention covered by any patent,without authority from the owner of the patent. PRECAUTIONSLABEL WARNINGI HARMFUL IF INHALED OR SWALLOWED. MAY CAUSE EYE,SKIN AND RESPIRATORY IRRITATION. Carefully read back panel for other cautions WARNINGI Contains petroleum distillates and xylene. Use in a well ventilated area.Prevent build-up of vapors by opening all windows and doors to achieve cross ventilation.Avoid breathing vapors.Avoid contact with eyes and skin. Prolonged or repeated exposure may affect the nervous system causing dizziness,headache or nausea. If you experience eye watering,headache or dizziness,leave the area to obtain fresh air. Do not swallow. FIRST AID: If swallowed do not induce vomiting,call a physician or Poison Control center immediately.For eye contact flush with water for 15 minutes,call a physician. For skin contact,wash thoroughly with soap and water. If overcome by vapors,get fresh air. KEEP OUT OF THE REACH OF CHILDREN. For more information,refer to the Material Safety Data Sheet(MSDS). WARNING:This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. NOTICE:Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain, nervous system,liver and kidney damage or may cause cardiac arrhythmia. INTENTIONAL MISUSE BY DELIBERATELY INHALING THE CONTENTS MAY BE HARMFUL OR FATAL Refer to the Material Safety Data Sheet(MSDS)for further Information OSI®QUAD®VOC Advanced Formula Sealant Page 2 of 3