10101 7TH AVE SE BLDG 5 2025-11-03

SimpsonFastening Connector/Steel-to-Wood Fastening 1 Strong,Dr►ve` SDS HEAVY-DUTY CONNECTOR Screw Heavy-Duty Simpson Strong-Tie Connectors The Simpson Strong-Tie Strong-Drive SDS screw is a 1/4"-diameter high-strength structural wood screw ideal for various connector installations as well as wood-to-wood, general metal-to-wood and EWP fastening applications. Install Tips:A low-speed 1/2"drill with a 3/s"hex driver(BITHEXR38-134)is the recommended tool for installation. Codes/Standards:ICC-ES ESR-2236(including City of LA Supplement);State of Florida FL9589 For more information,see p.68,C-F-2023 Fastening Systems catalog 0.48 SDS — Allowable Shear Loads — Steel Side-Plate Applications 11/2°-8" � DF/SP Allowable Loads' Allowable Loads' I I I I 1 Shear(100) Shear Withdrawal' 11 1 I I Wood Side Plate' Steel Side Plate (100) 1 13/4 14 ga. 10 ga. Wood Steel 1 1. 111 • 11/2 SCL 16 ga. and or Side Side II I I 12 ga. Greater Plate Plate 11/z SDS25112 1 1,500 — — 250 250 250 170 170 — — 180 180 180 120 120 2 SDS25200 11/4 1,300 — — 250 290 290 215 215 — — 180 210 210 150 150 0 21/2 SDS25212 11/2 1.100 190 — 250 390 420 255 255 135 — 180 280 300 180 180 • 3 SDS25300 2 950 280 — 250 420 420 345 345 200 — 180 300 300 240 240 31/2 SDS25312 21/4 900 340 340 250 420 420 I 345 385 245 245 1180 300 300 240 270 • 41/2 SDS25412 23/4 800 350 340 250 420 420 345 475 250 245 180 300 300 240 330 0 5 SDS25500 23/4 I 500 350 340 1 250 420 420 345 475 250 245 180 300 300 240 330 6 SDS25600 3% 1 600 350 340 1 250 420 420 345 560 1 250 245 180 300 300 240 395 6 8 1 SDS25800 31/4 1 400 350 340 250 420 420 345 1 560 1 250 245 180 300 300 240 395 1.Allowable loads are shown at the wood load duration factor of CD=1.00.Loads may be increased for load duration up to a CD=1.60. 11 2.Withdrawal loads shown are in pounds(Il and are based on the lessor value of either head pull-through for a 1.5"-thick wood side member or withdrawal from the main member.If entire thread length is not installed into the main member,calculate withdrawal based on 172 lb./in.of thread penetration for DF/SP wood and 121 lb./in.for SPl wood.Maximum withdrawal values with a steel side plate are 635 lb.for 16 ga.and 800 lb. for 14 ga.due to head pull-through. 3.LSL wood-to-wood applications that require 41h",5",6"and 8"SDS screws are limited to interior-dry use only. 4.Minimum spacing requirements are listed in ICC-ES ESR-2236. E E 2 Wafer-Head Screw 0 General Wood-to-Wood, Metal-to-Wood Fastening f For more information,see p.68,C-F-2023 Fastening Systems catalog 0.42" O o N SD8 — Allowable Shear Loads — Steel Side Plate -1 1/4" Reference Allowable 1.1 Tr 1 w r> 0 N LengthReference Size.x 11' Steel Side Plate Allowable I.1 LL 1 in. 1. Ob.)U 11 1 DFUSP DFL/SP #8 x 11/4 SD8x1.25 50 45 82 58 1.Allowable loads are shown at the wood load duration factor of CD=1.CC. Loads may be increased for load duration up to a CD=1.60. 2.SD8x1.25 requires 3/"minimum penetration into the main member. 3.Do not use SD8x1.25 wood screws with structural connectors unless specified. 4.Warning:Industry studies show that hardened fasteners can experience performance problems in wet or corrosive environments.Accordingly,use this product in dry,interior,and noncorrosive environments only. 202