Laserfiche WebLink
Simpson Strong-Tie',Wood Construction Connectors <br /> LUC/LU/U/HU/HUC <br /> Standard Face-Mount Joist Hangers <br /> LUC— Concealed-flange hanger available for 2x6,2x8, <br /> 2x10 and 2x12 lumber. Ideal for end of ledger/header ° rk•� <br /> or post conditions,the LUCZ also provides cleaner a m <br /> lines for exposed conditions such as overhead decks. <br /> ° <br /> LU —Value engineered for strength and economy. <br /> C ° <br /> M Precision-formed — engineered for installation ease ° ° ° <br /> = and design value. <br /> •in U —The standard U hanger provides flexibility of <br /> joist to header installation.Versatile fastener selection ° e <br /> 3 with tested allowable loads. <br /> fco <br /> HU/HUC— Most models have triangle and round ° <br /> holes.To achieve maximum loads,fill both round <br /> and triangle holes with common nails.These <br /> to heavy-duty connectors are designed for additional LU28 f°r U24) <br /> strength,longevity and safety factors. (except LU roughs) U210 HU214 <br /> Projection seat on most <br /> Material:See tables on pp. 104-114 models for maximum bearing <br /> Finish:Galvanized.Some products available and section economy. <br /> in ZMAX"coating or stainless steel. <br /> 0 0 <br /> Installation: <br /> o° <br /> • Use all specked fasteners;see General Notes. <br /> • HU/HUC— Can be installed filling round holes 0 ° Model configurations <br /> only,or filling round and triangle holes for ° ° may differ from those <br /> maximum values. o ° shown.Some HU <br /> • Joists sloped up to Y4:12 achieve table loads. models do not have <br /> • For installations to masonry or concrete ° ° triangle holes. <br /> see pp.243-245, ° ° °° °° ° Contact Simpson <br /> ° Strong-Tie. <br /> • HU/HUC hangers can be welded to a steel <br /> member.Allowable loads are the lesser of the <br /> values in the hanger tables on pp. 104-114 or <br /> the weld capacity— refer to technical bulletin <br /> T-C-HUHUC-W at strongtie.com. LUC210Z HUC412 <br /> (LUC26Zsimilar) Concealed flanges <br /> • When nailing into��,i'ra 3a:: carrying member's <br /> end grain,the allowable load is adjusted by a ° <br /> factor of 0.67. <br /> Allowable Loads: a< <br /> HU min.nailing— 0 0 <br /> • See table on pp. 104-114 for loads. fill round holes w <br /> F <br /> Options: HU max.nailing— n ° z <br /> fill round and °' o <br /> • For both flanges concealed,order HUC. triangle holes ° ° ° <br /> • When the HUC is skewed,the header flange ° o <br /> opposite the skew direction is not concealed. <br /> Seep. 101. N <br /> N <br /> • For low-cost,code approved 45°skewed <br /> hangers,see SUR/SUL. HU68 Typical LUCZ Installation o <br /> • For field-adjustable hangers,see LSSJ,LRUZ <br /> and LSSR on pp.117-119. <br /> • See modifications table for available options <br /> and associated load capacities for U and <br /> HU hangers. <br /> • For ease of ordering,refer to technical bulletin <br /> T-C-U-HU`,,VS at strongtie.com. ° I 0 <br /> • LU/LUC cannot be modified. W° <br /> 0 <br /> 0 <br /> 01 <br /> Typical HU Installation Typical LU28 Installation <br /> 100 <br />