Laserfiche WebLink
SimpsonStrong I Systems Technical Guide <br /> Deck Construction — Ledgers <br /> StrongirDri ve <br /> SDS, SDWS and SDWH HDG Sawn Lumber <br /> Deck Ledger to Band Joist Applications (cont.) <br /> Allowable Shear Loads for Attachment of Lumber Deck Ledger to <br /> Band Joist (cont.) <br /> Nominal Screw A'lowable <br /> Model Band Joist <br /> Fastener Ledger Length Size .., <br /> Size (in.) No. Minimum� i (lb.) <br /> MMM <br /> • 1"OSB OR 1"LVL 160 <br /> mm <br /> 1 Ya"OSB 225 <br /> 2x 4 SDWS27400SS <br /> 15/,s"LVL OR 1 Ya"LSL 225 <br /> • Strong Drive 2x Nominal Sawn Lumber 225 <br /> TIMBER SS <br /> Screw 1"OSB OR 1"LVL 190 <br /> 1 Y6"OSB 190 <br /> • 2-2x 5 SDWS27500SS <br /> � 15/,6"LVL OR 1 1/<"LSL 190 <br /> 2x Nominal Sawn Lumber 190 <br /> 1"OSB OR 1"LVL 280 <br /> 1'/6"OSB 280 <br /> 2x 4 SDWH27400G <br /> � 15/i6'LVL OR 1 Ya"LSL 280 <br /> Strong Drive SDWH 2x Nominal Sawn Lumber 280 <br /> TIMBER-HEX HDG Screw 1"OSB OR 1"LVL 315 <br /> 1'A"OSB 315 <br /> 2-2x 6 SDWH27600G <br /> 15/,6"LVL OR 1 Y<"LSL 315 <br /> 2x Nominal Sawn Lumber 315 <br /> 1.Specific gravity of the solid sawn band joists and ledgers shall be typical of species combinations with 0.42 5 SG s 0.55. <br /> 2.Multiple ledger plies shall be fastened together per code independent of the SDS,SDWS or SDWH fasteners listed in the table. <br /> 3.Allowable loads are shown at the wood load duration factor of Co=1.0.Loads may be increased for load duration by the building <br /> code up to a CD=1.6. <br /> 4.Structural sheathing between the ledger and band joist shall be a maximum of 1h"thick and fastened per code. n <br /> 5.See Screw Spacing Deta l on the following page for spacing requirements. o <br /> 6.End screws shall be located near the bottom of the ledger.For end distances between 2"and 6",use 50%of the load and 50% m <br /> of the standard spacing between the end screw and the adjacent screw.For end distances between 2"and 4",predrill using a'hz" <br /> drill bit for SDWH27SS fasteners,a 3/,e"drill bit for the SDWH27G and SDWS27SS fasteners,a 1/3z"drill bit for SDS,SDWS22DB, <br /> and SDWHI9SS fasteners,and a'A'drill bit for SDWH19DB. rn <br /> 7.Visit strongtie.com/drawings and search for SD1-L for additional ledger fastening detail sheets and load tables in DWG,PDF <br /> or DXF format. n <br /> E <br /> M <br /> N <br /> O <br /> N <br /> a <br /> U <br /> M <br /> N <br /> O <br /> N <br /> CU <br /> 168 <br />