Laserfiche WebLink
Simpson Strong-Tie' Wood Construction Connectors <br /> LU C/LU/U/H U/HUC <br /> Standard Face-Mount Joist Hangers <br /> LUC-Concealed-flange hanger available for 2x6,2x8, <br /> 2x10 and 2x12 lumber.Ideal for end of ledger/header <br /> or post conditions,the LUCZ also provides cleaner <br /> lines for exposed conditions such as overhead decks. <br /> tm LU -Value engineered for strength and economy. <br /> Precision-formed -engineered for installation ease <br /> and design value. ° ° H • <br /> N U -The standard U hanger provides flexibility of <br /> joist to header installation.Versatile fastener selection ° • ° <br /> C with tested allowable loads. • ° ° <br /> HU/HUC- Most models have triangle and round <br /> Cn holes.To achieve maximum loads,fill both round <br /> and triangle holes with common nails.ThesefOrU <br /> NLU28 heavy-duty connectors are designed for additional 24) <br /> strength,longevity and safety factors. (except U roughs) U210 HU214 <br /> Projection seat on most <br /> Material:See tables on pp.104-114 models for maximum bearing <br /> Finish:Galvanized.Some products available and section economy. <br /> in ZMAX®coating or stainless steel. <br /> 0 0 <br /> Installation: ° <br /> • Use all specified fasteners;see General Notes. <br /> • HU/HUC-Can be installed filling round holes p <br /> Model configurations <br /> only,or filling round and triangle holes for go <br /> may differ from those <br /> maximum values. shown.Some HU <br /> Joists sloped up to 1/4:12 achieve table loads. • models do not have <br /> For installations to masonry or concrete v° triangle holes. <br /> see pp.243-245. • Contact Simpson <br /> • Strong-Tie. <br /> • HU/HUC hangers can be welded to a steel / • __ <br /> member.Allowable loads are the lesser of the <br /> values in the hanger tables on pp.104-114 or <br /> the weld capacity-refer to technical bulletin <br /> T-C-HUHUC-W at strongtie.com. LUC210Z HUC412 <br /> (LUC26Zsimilar) Concealed flanges <br /> • When nailing into s� d sa:�r�carrying member's <br /> end grain,the allowable load is adjusted by a <br /> factor of 0.67. <br /> Allowable Loads: <br /> HU min.nailing— ° 8 <br /> • See table on pp.104-114 for loads. k, fill round holes F <br /> Options: HU max.nailing— o ° z <br /> fill round and o <br /> • For both flanges concealed,order HUC. triangle holes ° fE <br /> • When the HUC is skewed,the header flange ° o <br /> m <br /> opposite the skew direction is not concealed. <br /> See p.101. <br /> • For low-cost,code approved 451 skewed <br /> hangers,see SUR/SUL. HU68 <br /> • For field-adjustable hangers,see LSSJ,LRUZ Typical LUCZ Installation U <br /> and LSSR on pp.117-119. ° <br /> • See modifications table for available options <br /> and associated load capacities for U and <br /> HU hangers. <br /> • For ease of ordering,refer to technical bulletin <br /> T-C-U-HU-WS at strongtie.com. ° ° <br /> • LU/LUC cannot be modified. }° <br /> o <br /> 0 <br /> Typical HU Installation Typical LU28 Installation <br /> 100 <br />