2831 W MARINE VIEW DR REVIVE BOWLS 2025-12-02

INSTALLATION (2 of 2) Table Riser Height Needed Risers Required TELEGLIDE RISER(24 SERIES) 0-3-1/2" None(use adapter) INSTALLATION GUIDELINES 5"-23" SR24 Tools needed:7/16"Nut drivertool/bit(included),marker(included), Adapter >23"-38" LR24 tape measure and drill with 1/2"chuck.Jigsaw,circular saw or reciprocating saw will be needed if risers need to be cut. NOTE:To remove a component or adjust its position,the Upper Band Clamp needs to be loosened or removed using nut driver bit. Loosened clamps should be retightened to 5-8 ft lbs.of torque SR24 1 (same as a rubber no-hub coupling).The Lower Band Clamp is Adapter factory set and should not be adjusted or removed. Short Riser Riser Riser Assembly Instructions/Steps HeightNeeded 1. Set unit so the pipe connections line up with jobsite piping and Riser measure riser height needed from top of cover to finished grade. T_J See Table 1 to select risers needed. Alignment Mark ]'or 2" 2. Remove covers from adapters.Remove adapters from main unit. -- --- ----- - 5„ On a level surface,pre-assemble the risers and adapters,adjusting the components upwards or downwards to achieve the riser height LR24 Cut Line needed.Make sure to maintain minimum and maximum insertion Long Riser, —————— depths as shown in Figure 2. If components are too long,make a circular line around the sidewall with marker and cut with a power saw.The lowest cut line on the riser assembly will be 5"beyond the 4"(w/standard connections) riser height needed to allow for ideal insertion depth(See Figure 1). An alignment mark should be drawn 1-2"beyond the riser height (3"for GB-35 w/4"connections) needed(depending on connection size)which will align with the top of the base unit gasket.DO NOT cut the alignment mark.The Components Figure 1-Riser Measurements Adapters and risers should sit level with each other.Tighten upper clamps to keep riser/adapter assembly from shifting.Make alignment marks on the sidewalls at the top of all riser gaskets to aid final assembly. Cover 3. IMPORTANT:Before the next step, make sure both diffusers are installed inside the main unit at the appropriate locations. Check if there needs to be any flow control adjustment at the inlet diffuser(see general installation instructions). Adapter(shown) or Riser 4. Take apart riser assembly and clean all sidewalls and insides of gaskets to remove dust/debris.Install components into the main Gasket unit starting from the lowest riser and work your way up to - - - - - - - - - - - - - - - - - - finished grade.Maintain minimum and maximum insertion Upper Band Clamp depths for all components(see Figure 2).Tighten Upper Clamps 2-112"Minimum Insertion Depth (field adjustable) to specified torque after correctly positioning components.Riser assembly may need to be supported during backfill. Lower Band Clamp (factory set do- 4"Maximum Insertion Depth 5. If tilting of the adapter is required to be flush with grade,do so (into GB unit only) adjust or remove) not AFTER all clamps have been tightened with riser(s)/adaptor in a - - - - - - - - - - - - - - - - - GB Unit(shown) vertical and level position.Tilting is done using gasket flexibility. or Riser Tilting before tightening clamps may ruin a perfect gasket seal. Schier recommends tilting only the adapter versus the entire riser assembly to make sure your riser height and proper tank DepthsFigure 2-Insertion access is maintained. 6. If riser height conditions change after completing above steps, there may be room for adjustment.As long as minimum and maximum insertion depths are maintained(see Figure 2),the adapters/risers can be adjusted/cut as many times as necessary. When riser system installation is complete,see Leak/Seal Testing procedure if required(p3 of 5). . 0 MODEL NUMBER: DESCRIPTION:Polyethylene Grease Interceptor GB-35 35 GPM-35 gallon capacity - PART it:4020-001-XX DWG BY:B.Karrer DATE:10/08/2015 REV: 4 10/13/2017 ECO: 057-0840-02 page 5 of 6