3003 W CASINO RD BLDG 40-53 2025-12-01

Sprinkler 123b January 17, 2014 C ESFR PENDENT SPRINKLER N I KJ NG4 VK503 (K16.8) The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Finish Suffix: Brass =A Temperature Suffix: 165 °F (74 °C) = C, 205 °F (96 °C) = E For example, sprinkler VK503 with a Brass finish and a 165 °F (74 °C)temperature rating = Part No. 14073AC. Available Finishes And Temperature Ratings: Refer to Table 1. Accessories: (Also refer to the"Sprinkler Accessories"section of the Viking data book.) Sprinkler Wrench: Part No. 13635W/B(double-ended wrench - Use Side A. Side B is for use with K25.2 ESFR Pendent Sprinkler VK510)Available since 2006. Sprinkler Cabinet: Twelve-head capacity: Part No. 01725A(available since 1971) 4. INSTALLATION WARNING: Viking sprinklers are manufactured and tested to meet rigid requirements of the approving agency. The sprinklers are designed to be installed in accordance with recognized installation standards. System design must be based on ESFR design guidelines described in the latest edition of Viking technical data, applicable FM Global Loss Prevention Data Sheets, the latest NFPA Standards, the latest standards of Verband der Sachversicherer (VdS), Loss Prevention Council (LPCB), the Authorities Having Jurisdiction,and also with the provisions of governmental codes,ordinances,and standards whenever applicable. Deviation from the standards or any alteration to the sprinkler after it leaves the factory including, but not limited to: painting, plating, coating, or modification, may render the sprinkler inoperative and will automatically nullify the approval and any guarantee made by The Viking Corporation. A. Sprinklers must be handled with care. They must be stored in a cool, dry place in their original shipping container. Never install sprinklers that have been dropped or damaged in any way. Such sprinklers should be destroyed immediately. NOTE: Wet pipe systems must be provided with adequate heat. B. The sprinklers must be installed after the piping is in place to prevent mechanical damage. Before installing, be sure to have the appropriate sprinkler model and style, with the correct orifice size, temperature rating, and response characteristics. C.With the sprinkler contained in the plastic protective cap,apply a small amount of pipe-joint compound or tape to the male threads only, while taking care not to allow a build-up of compound in the sprinkler orifice. D. Use ONLY sprinkler wrench 13635W/B (shown in Figure 1)for installing ESFR Sprinkler VK503! With the sprinkler con- tained in the protective cap, install the sprinkler onto the piping by applying the sprinkler wrench to the sprinkler wrench flats only, while taking care not to damage the sprinkler operating parts. DO NOT use any other type of wrench, as this could damage the unit. DO NOT use the sprinkler deflector or fusible element to start or thread the sprinkler into a fitting. DO NOT exceed 50 ft. lbs.of torque(hand tight, plus approximately two full turns with the wrench)to install these sprinklers. Higher levels of torque may distort the sprinkler inlet with consequent leakage or impairment of the sprinkler. E.After installation,the entire sprinkler system must be tested.The test must be conducted to comply with the Installation Standards. Make sure the sprinkler has been properly tightened. If a thread leak occurs, normally the unit must be removed, new pipe-joint compound or tape applied, and then reinstalled.This is due to the fact that when the joint seal is damaged,the sealing compound or tape is washed out of the joint. Immediately replace any damaged units, using the special sprinkler wrench only. TABLE 1:AVAILABLE SPRINKLER TEMPERATURE RATINGS AND FINISHES Sprinkler Temperature Sprinkler Nominal Maximum Ambient Frame Paint Classification Temperature Rating' Ceiling Temperature' Color Ordinary 165 °F (74 °C) 100 °F (38 °C) None Intermediate 205 °F (96°C) 150 °F (65 °C) White Sprinkler Finish: Brass Footnotes The sprinkler temperature rating is stamped on the deflector. z Based on NFPA-13.Other limits may apply,depending on fire loading,sprinkler location,and other requirements of the Authority Having Jurisdiction. Refer to specific installation standards.