3003 W CASINO RD BLDG 40-26 2025-12-01

(I) TOLCOt' www.tolco.com Fig. 980 - Universal Swivel Sway Brace Attachment C @US LISTED Size Range — One size fits bracing pipe 1" thru 2", TOLCO 12 gauge channel, and all <FM > structural steel up to 1/4" thick. Material — Carbon Steel Component of State of California OSHPD Approved Function — Multi-functional attachment to structure or Seismic Restraints System braced pipe fitting. Features — This product's design incorporates a concen- tric attachment opening which is critical to the performance H of structural seismic connections. NFPA 13 (2010) 9.3.5.8.4 indicates clearly that fastener table load values are based only on concentric loading. Mounts to any surface angle. Break off bolt head assures verification of proper installation. Installation — The Fig.980 is the structural or transitional A attachment component of a longitudinal or lateral sway brace assembly. It is intended to be combined with the B "bracing pipe" and TOLCO "braced pipe" attachment, Fig. 1000, 1001, 2002, 4L, 4A or 4B to form a complete bracing assembly. NFPA 13 and/or OSHPD guidelines should be followed. To Install — Place the Fig. 980 onto the "bracing pipe". Tighten the set bolt until set bolt head breaks off. Attachment can pivot for adjustment to proper brace angle. Approvals — Underwriters Laboratories Listed in the USA (UL) and Canada (cUL). Approved by Factory Mutual Engineering (FM). Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to the TOLCO Seismic Restraint Systems Guidelines. Note — The Fig. 980 Swivel Attachment and the Fig. 1001, Fig. 1000, Fig. 2002, Fig. 4A, Fig. 4B or Fig. 4L Pipe Clamp make up a sway brace system of UL Listed attachments and bracing materials which satisfies the require- ments of Underwriters' Laboratories and the National Fire Protection Association (NFPA) Finish — Plain Note — Available in Electro-Galvanized finish. Order By — Figure number and finish. - Pat. #6,273,372, Pat. #6,517,030, Pat.#6,953,174, Pat. #6,708,930, Pat. #7,191,987, Pat.#7,441,730, Pat. #7,669,806 Lateral Brace Dimensions •Weights Max.Design Max. Design Approx. A B H* Load Lbs. Load Lbs.** (cULus) (FM) Wt./100 51/4 1 7/8 17/32 2765 2800 132 Available with hole sizes to accommodate up to 3/4"fastener. Consult factory. The loads listed are axial loads on the brace.The horizontal load capacity, H,of the brace is: H=F x sin 0,where 0 is the installation angle measured from the vertical. TOLCO®brand bracing components are desgined to be compatible ONLY with other TOLCO®brand bracing components,resulting in a Listed seismic bracing assembly. DISCLAIMER — NIBCO does NOT warrant against the failure of TOLCO®brand bracing components, in the instance that such TOLCO®brand bracing components are used in combination with products, parts or systems which are not manufactured or sold under the TOLCOO brand. NIBCO shall NOT be liable under any circumstance for any direct or indirect,incidental or consequential damages of any kind, including but not limited to loss of business or profit,where non-TOLCO brand bracing components have been,or are used. OFFICE/MANUFACTURING FACILITY•1375 SAMPSON AVE.•CORONA,CA 92879•PH: 951.737.5599•FAX: 951.737.0330 CUSTOMER SERVICE•800.786.5266 www.tolco.com