|
SECTION 23 30 l3 13 on drawings.Static pressure requirements shall be precise end
<br /> SPECIFICATIONS curate{air vrlod! not olune InI—' tion sheµ be accurate within
<br /> TAG.Commercial Kitchen Ventilation Hoods,Listed Conmercihl Kitchen Hoods loft Increments along the length of the ventilator.
<br /> PART I-GENERAL
<br /> 1.1 SUMMARY U CONSTRUCTION
<br /> A.The BD2 series Is a Type I,tow proxbdty hood for use over 600'F A.Construction shell be t
<br /> eking surface temperatures. The lee Proximity hand refers to the type 430 stalMess steel.
<br /> close location of the hootl with respect to the cooking oppllmues. B.Double well insulated front to wMinate condensation and Increase
<br /> B.the hood shalt have the size,shape,and performance specified ort Iplrltyy on wide sizes.The insulation shall have a flexural modulus of
<br /> drawings. 475 Eli meet UL 101 requirements and be In accordance with NFPA 90A
<br /> and 90B
<br /> C,Hood shall be equipped with a minimum of four connections for
<br /> 12 SUBHITTALS hanger rods.Hood lengths greater than 12'w111 have added hangers.
<br /> A.The manufacturer assumes no liability for the use or results of A Exhaust duct cotter to be 4'hfgh with flange.
<br /> use Fran this docment.Speclflcatlo s are to be reviewed by the E.The rease drain system shalt be an enclosed Irateggrrnal part of the
<br /> engineer to conflrn the projects requirements and meet Federal, hood bock and have slo es with an ex osed,remavoWe 1/2
<br /> state,and Local codes and regulations, cup to facilitate clean.pg. p grease
<br /> B.As the manufacturer continues product development,It rese es F,Hood shall be furnished with UL classified filters,supplied In size
<br /> the right to Change design and spedficatlons without notice.ry (WpI
<br /> and quantity as required by ventilator.
<br /> C.The manufacturer shall supply complete computer generated G.All seams shell be welded and have stainless steel on d
<br /> submittal drawings,Including hood section vler(s)and hood plan surfaces expose
<br /> j view(s).These drawings must be available to the englneer,architect,
<br /> and owner for theh use in construction,operation,and nafnterance.
<br /> 2.3 LIGHTWG
<br /> 1.3 QUALITY ASSURANCE A.L55 SerRIs canopy light fixture,Includes clear thermal and shock
<br /> A.This hood Is ETL-listed to standard 1.11-710,ULC710,and ULC-S646 resistant Qlobe,
<br /> when Installed In accordance with these Installation Instructions and 2.4 FILTERS
<br /> National Fire Protection Assodntlon Standard NFPA%,Standard Poe
<br /> Ventilation Control and Fire Protection of Commercial Cooking A.Hanging
<br /> ee^G rot St a ei s e ff l Steel
<br /> Baffle Filter with Handles and Rattan
<br /> Operations.' d 9
<br /> B.Built-In conplionce with NSF/ANSI Standard 2,
<br /> C,The hood shall be ETL Listed as, 25 ACCESSORIES
<br /> 1. Exhaust Hood Without Exhaust Damper. A.End Panel(s)r W..hood perfornonce and wininate the effects of
<br /> F crass drafts In the kitchen.Wets constructed of stainless steel
<br /> 2.E7L Sanitation Listed and built In accordance with NFPA 96. and shed according to hood width and okirp equipment.Exposed
<br /> 3,The ETL label shall list temperature ratting(s)and ntninum CFH/ft edger hemmed For safety and rigidity.
<br /> Selected panels,
<br />'f rattng(s). 1.Quarter End Panel
<br /> i
<br /> f L4 VARRANTY PART 3-EXECUTION
<br /> f A.Ali units shall be prodded with the following standard warranty, 3.1 EXAMINATION
<br /> f 1.This equipment Is warranted to be free From defects In materials A Examine areas and conditions under which the syy ten Is Installed Do
<br />(( end w—k—ship,under normal use and service,For a period of not proceed with work until unsatisfactory wadi{Ions have been
<br /> 2-years from ante of shipment. c arrecUd in a manner acceptable to Installer.
<br />€- B.The ox+focturer shall not be liable for 4icidental and consequential
<br />[- l aosses and damages potentially attrioutoble to nnlfunctfantng
<br /> eq,Apnwnt.Should any part of the equipment prove to be defective 3.2 INSTALLATION
<br /> In material ar woriunanship within Iha 2-year my period,upon A.Install in accordance with manafocturer's Instructions,drnrings,
<br /> examination by the manufacturer,such part wNl be repaired or written specl{Italians,manufacturer's Installation manual,and all
<br /> placed by manufacturer at Jorge.Tina buyer shall pay all applicable bu0dJ�gca codes.
<br /> labor costs Incurred In connection with such repeh or replacement
<br /> Equipment shall not be returned without manufacturer's prior
<br /> authorletion,and all returned equipment shall be sapped by the
<br /> buyer,freight prepaid to a destination deternIned by the
<br /> manufacturer.
<br /> C.Refer to Manufacturers Operation,Instaeatlon,and Maintenance
<br /> ((IIH)Manuel for drtaned descriptions of what Is/Is not covered and
<br /> contact Information for warranty claims,
<br /> E'
<br /> PART 2 -PRODUCTS
<br /> 2.1 GENERAL
<br /> A.Construction shalt be dependent the structural ap
<br /> plication ppdcatlon to
<br /> p-tdistortion and other defects.All seats,joints,and
<br /> penetrations of the hood enclosure to the tower puts or e
<br /> peMust r,which directs and captures grensa-Ious vapor not
<br /> exhaust gases,shall have a Uqu1d-tight continuous external weld in
<br /> accordaxe with NFPA%.
<br /> B.Duct sizes,CfH.and static pressure requdrenents shall be as shown
<br /> ✓OBMemo's Everett - R3
<br /> 00 LOCATION EVERETT, WA, 98203
<br /> econeair
<br /> D.4TE 8/3/2021 JOB # 5020274
<br /> DWC # 3 DR4WN BY
<br /> REY. S'C.4LE 1/4' = 1'-0'
<br />
|