Laserfiche WebLink
8 7 6 5 4 3 2 1 <br /> MOUNTING TO BRICK OR SPLIT ROCK 3" DEEP , Rev: DESCRIPTION: DATE: APPROVED: <br /> STAINLESS STEEL ifA INITIAL RELEASE 3/21 /12 LO <br /> 1/4 FLAT WASHER Lul B INITIAL RELEASE 05/03/12 RCW <br /> STAINLESS STEEL oolco G C INTALL INSTRUCTIONS AND NOTES WERE UPDATED 06/11 /12 RCW <br /> D 1 1 /4-20 NUT = D INSTALL INSTRUCTIONS UPDATED TO 07/05/12 RCW <br /> 4 INCLUDE MOUNTING TO EIFS AND TILE <br /> m — (1 7) #8 FLAT HEAD SS INSTALLATON INSTRUCTIONS: <br /> STAINLESS STEEL /SHEET METAL SCREWS 1. REMOVE FACE BY REMOVING (17) #8 PHILLIPS FLAT <br /> 1 /4-20 THREADED ROD FOR FACE ATTACHMENT HEAD SCREWS AROUND PERIMETER OF FACE. PULL <br /> FACE OFF OF BACK. <br /> CHASE NIPPLE 2. POSITION AS REQUIRED, MARK MOUNTING AND CABLE <br /> STAINLESS STEEL DETAIL A LOCATIONS. <br /> n 1 /4-20 NUT SCALE 1 : 1 _ CONDUIT FOR 120 VOLT 3. PRE-DRILL (5) 3/8" DIA X 3'' DEEP HOLES IN THE WALL <br /> wWIRING PER CODE FOR THE 1/4-20 THREADED RODS. ENSURE A 1" MIN <br /> V) EMBEDMENT OF THE ROD INTO THE WALL. (PROVIDED <br /> STAINLESS STEEL 6'' LAGS SHOULD BE USED FOR TOP MOUNTING HOLES <br /> 1/4 LOCK WASHER STAINLESS STEEL IF V EMBEDMENT IS NOT ACHIEVED.) <br /> Z 1 /4 FLAT WASHER 4. DRILL CLEARANCE HOLE FOR THE CABLE AND FITTING. <br /> N 5. ATTACH THE THREADED RODS THROUGH THE METAL <br /> m BACK AS SHOWN IN DETAIL A. <br /> ATTACH FACE TO BACK (17) LOCATIONS. <br /> 6. MAKE FINAL ELECTRICAL CONNECTIONS. IF ELECTRICAL <br /> A IS NOT PROVIDED CONTACT EVERBRITE. <br /> 7. TEST LIGHT. TAKE PHOTOS. (NOTE: BE SURE TO PUSH <br /> WIRE BACK THROUGH THE CONDUIT BEFORE <br /> 0 <br /> ATTACHING SIGN TO THE WALL.) <br /> Z 8. CLEAR DUST FROM THE 3/8'' HOLES IN THE WALL. INSERT <br /> ADHESIVE INTO THE 3/8" HOLES IN WALL. <br /> w #8 SHEET METAL 9. SILICONE ALL WALL PENETRATIONS <br /> N SCREW TYP 10. MOUNT SIGN TO WALL BY SLOWLY PUSHING THE <br /> THREADED RODS INTO THE HOLES FILLED WITH <br /> ADHESIVE. <br /> 0 11 . ENSURE TOGGLE SWITCH IS IN ON POSITION. <br /> (2) 1 /4-20 X 6 THREADED RODS STAINLESS STEEL (USE IF NEEDED) <br /> (5) 1/4-20 X 4" THREADED RODS STAINLESS STEEL DESIGN NOTES: <br /> 6, <br /> �5) <br /> 10) 1 /4-20 NUTS STAINLESS STEEL 1 . THISSIGN IS INTENDED TO BE INSTALLED IN <br /> 3 1 /4'' LOCK WASHERS STAINLESS STEEL ACCORDANCE WITH THE REQUIREMENTS <br /> P B /. (10) 1 /4'' FLAT WASHERS STAINLESS STEEL OF ARTICLE 600 OF THE NATIONAL B <br /> • (AS REQUIRED) ADHESIVE ELECTRICAL CODE AND ALL OTHER <br /> PPLICABLE LOCAL CODES. THIS• BY EVERBRITE) THE PROPER GROUNDING OF THE ISIGN. DES <br /> 2. LED-ILLUMINATED SIGN: NEC CLASS 2 LED <br /> o ELECTRICAL SYSTEM. <br /> 3. POWER SUPPLY: INPUT: 120-277 VAC, 50-60 <br /> $ Hz, 75W MAX OUTPUT: 24VDC, VOLTAGE <br /> op REGULATED, APPROXIMATE 24 WATTS; <br /> N OPERATION ENVIRONMENT: WET, DAMP, <br /> s' DRY, -25DEG C TO +60 DEG C. <br /> 4. (1) 15AMP CIRCUIT REQUIRED <br /> 0 <br /> UNLESS OTHERWISE SPECIFIED: <br /> NAME DATE PRODUCT: <br /> DIMENSIONS ARE IN INCHES <br /> TOLERANCES: DRAWN Lo 3/21/12 MCD NEXTGEN 42'' ARCH <br /> S FRACTIONAL±1/8 <br /> ° SQUARE FOOT AREA: X -'.Db XX .03 <br /> CHECKED <br /> jA SEE DETAIL I L A A .XXX=±.°15 .XXXX=REAM DESIGNED A <br /> FOR ATTACHMENT ANGULAR: <br /> MACHINED± .5 BEND±1 CUSTOMER SERV. TITLE: <br /> INSTRUCTIONS BOXED: 14 SQ. FT. FINISH ENGAFPR. INSTALL,MCD NG 42" ARCH <br /> U ••• <br /> •s�•••s� PROPRIETARY AND CONFIDENTIAL <br /> Everbd <br /> THE INFORMATION CONTAINED IN THIS SIZE DWG. NO. REV <br /> V) •� �• DRAWING IS THE SOLE PROPERTY OF <br /> " DESIGNED WINDLOAD: 150 MPH WIND SPEED 3-SECOND GUST EXPOSURE. •:•��;•:•.A ysygm Dlymon IN <br /> fORAS ANY REPRODUCTION B IN449582S <br /> O NEXT ASSY USED ON IN PART OR AS A WHOLE <br /> (`1 WITHOUT THE WRITTEN PERMISSION OF <br /> COMPLIANT WITHNATION BUILDING CODES AND STANDARDS (IBC, UBC) EVERBRITE LLC.IS STRICTLY PROHIBRED. 71 <br /> APPLICATION DO NOTSCA_EDRAWING SCALE: 1:10 TYPE: PART <br /> 8 7 6 5 4 3 2 __. � r <br />