4132 FEDERAL AVE 2016-08-22 - Laserfiche WebLink

■ ■ ■ • • ML 1:116,14 2012 Washington State Energy Code Compliance Forms for Commercial,Group R1,and>3 story R2 and R3 Revised June 2013 Project Address 4132 Federal Ave Date 2/3/2016 The following information is necessary to check a mechanical permit application for commercial provision compliance with the 2012 WSEC. NOTE:Define print area in Excel prior to printing MECH-CHK pages. Applicability Code Section Code Provision Information Required Location Building Department _T(yes,no,na) on Plans Notes GENERAL PROVISIONS,CONTINUED HVAC System Controls&Criteria,Continued C403.2.12 Variable flow control- Indicate fan&pump motors requiring VF control&method(VSD or equiv N/A fans/pumps controls N/A C403.2.12.1 Variable flow control- Indicate cooling tower fans requiring variable flow control and method cooling towers C403.2.12.2 Large volume fan systems Indicate fan systems requiring airflow reduction based on heating and N/A cooling demand;or exception taken C403.2.12.2 Single zone AC systems Indicate method of cooling demand-based fan control for sys.>110,000 N/A I I btuh N/A C403.2.4.10 DDC system capabilities Identify all DDC system input/output control points and indicate capability Ducting Systems C403.2.7.1 & Indicate all ductwork constructed and sealed per IMC,C402 leakage N/A C403.2.7.3 Duct construction require ents and IBC vapor retarder requirements N/A 403.2.7.3.1_ Duct pressure Identify location of low,medium and high pressure ductwork on plans classifications C403.2.7.3.3 High pressure duct leakage Indicate high pressure duct leakage testing requirements on plans;provide N/A test test results to jurisdiction when completed N/A C403.2.7.1/ Duct insulation Indicate R-value of insulation on ductwork Piping Systems N/A C403.2.8 Piping insulation Indicate R-value of insulation on piping N/A C403.2.8.1 Piping insulation exposed to Indicate method of protection from damage/degredation weather SIMPLE SYSTEMS Qualifying Systems YES C403.3 Qualifying single zone Verify unitary or packaged equipment does not exceed capacity limits,does systems not have active humidification or simultaneous heating/cooling C403.3 Qualifying 2-pipe heating Verifyi e heating-onlysystem does not exceed ca limits N/A systems 2-pipe p y capacity N/A C403.3.2 Hydronic system controls Refer to Complex Systems Section C403.4.3 Simple System Economizers N/A C403.3.1 Air economizer required Indicate cooling systems requiring economizer controls,note in equip sched. N/A C403.3.1.1.1 Air economizer capacity Indicate modulating OSA control capability up to 100%OSA,or exception N/A C403.3.1.1.3 Air economizer high limit Indicate high limit shut-off control method per Table C403.3.1 1.3(2) controls N/A C403.1.1.2 Integrated air economizer Indicate capability for partial air economizer operation for systems with operation capacity>65,000 btuh N/A C403.3.1 Air economizer exceptions Indicate eligible exception(s)taken and provisions to comply with exceot on(s) COMPLEX SYSTEMS Complex System Economizers C403.4.1 Air economizer required Indicate cooling systems requiring economizer controls;note in equip NIA sched. C403.4.1.4 Economizer heating system Verify control method of HVAC systems with economizers does not N/A impact increase building heating energy usage during normal operation N/A C403.4.1.3 Integrated economizer Indicate capability for partial economizer operation for air or water econo operation systems Moved Water economizer capacity Indicate water econo capable of 100%cooling capacity at 50°F db/45°F wb N/A OSA C403.4.1.2 Water economizer Indicate precooling coils and heat exchangers do not exceed pressure drop N/A maximum pressure drop limit N/A C403.3.1 Air economizer exceptions Indicate eligible exception(s)taken and provisions to comply with