2715 HEWITT AVE SUBWAY 2016-10-03

2012 Washington State Energy Code Compliance Forms for Commercial,Group R1,and>3 story R2 and R3 Revised June 2013 Project Address 2715 Hewitt Avenue Date 1/3/2014 The following information is necessary to check a mechanical permit application for commercial provision compliance with the 2012 WSEC. N9.TE:Define r' area in Excel Prior to printingMECH-CHK pages. Applicability Location on Building Department (yes,no,na) Code Section Code Provision Information Required Plans Notes GENERAL PROVISIONS,CONTINUED HVAC System Controls&Criteria,Continued C403.2.12 Variable flow control- indicate fan&pump motors requiring VF control&method(VSD or equiv na fans! um s controls C403.2.12.1 Variable flow control- Indicate cooling tower fans requiring variable flow control and method na cooling!Owers C403.2.12.2 Large volume fan systems Indicate fan systems requiring airflow reduction based on heating and cooing na demand;or exception taken C403.2.12.2 Single zone AC systems Indicate method of cooling demand-based fan control for sys.>110,000 btuh na na C403.2.4.10 DDC system capabilities Identify all DDC system input/output control points and indicate capability for Ducting Systems C403.2.7.1& Duct construction Indicate all ductwork constructed and sealed per IMC,C402 leakage Yes C403.2.7.3 requirements and IBC vapor retarder requirements M-1 yes C403.2.7.3.14 Duct pressure classifications Identify location of low,medium and high pressure ductwork on plans M_ C403.2.7.3.3 High pressure duct leakage Indicate high pressure duct leakage testing requirements on plans;provide na test test results to jurisdiction when completed Yes C403.2.7.1/2 Duct insulation Indicate R-value of insulation on ductwork M_1 Piping Systems na C403.2.8 Piping insulation Indicate R-value of insulation on piping na C403.2.8.1 Piping insulation exposed to Indicate method of protection from damage/depredation weather SIMPLE SYSTEMS Qual Eying Systems e5 C403.3 Qualifying single zone Verify unitary or packaged equipment does not exceed capacity limits,does M-1 Y systems not have active humidifcation or simultaneous heating/cooling C403.3 Qualifying 2-pipe heating Verify 2-pipe heating-only system does not exceed capacity limits na systems na C403.3.2 Hydronic system controls Refer to Complex Systems Section C403.4.3 Simple System Economizers Yes C403.3.1 Air economizer required Indicate cooling systems requiring economizer controls;note in equip sched. M-1 yes C403.3.1.1.1 Air economizer capacity Indicate modulating OSA control capability up to 100%OSA,or exception M-1 yes C403.3.1.1.3 Air a controls omizer high limit Indicate high limit shut-off control method per Table C403.3.1.1.3(2) M C403.1.1.2 Integrated air economizer Indicate capability for partial air economizer operation for systems with M-1 Yes oeratlon Icaparity>65,000 btuh na C403.3.1 Air economizer exceptions Indicate eligible exception(s)taken and provisions to comply with COMPLEX SYSTEMS Complex System Economizers C403.4.1 Air economizer required Indicate cooling systems requiring economizer controls;note in equip sched. 9C403.4.1.4Economizer heating system Verify control method of HVAC systems with economizers does not increase impact building heating energy usage during normal operation Integrated economizer Indicate capability for partial economizer operation for air or water econos tems Water economizer capacity Indicate water econo capable of 100%cooling capacity at 50°F db/45°F wb OSA C403.4.1.2 Water economizer maximum Indicate precooling coils and heat exchangers do not exceed pressure drop pressure drop limit C403.3.1 Air economizer exceptions Indicate eligible exception(s)taken and provisions to comply with �f i