3305 NASSAU ST WA CENTER FOR PAIN MANAGEMENT 2016-10-04

2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2 8 R3 over 3 stories and all R1 Revised Nov 2013 Project Address Washington Centerfor Pain Management: Everett Date 5/21/2013 The following information is necessary to check a permit application for compliance with the lighting, motor, and transformer requirements in the Washington State Energy Code, Commercial Provisions. Applicability Location in Building Department (yes,no,na) Code Section Component Compliance information required in permit documents Documents Notes LIGHTING CONTROLS (Section C405.2) C405.2.1.1 Manual interior lighting Indicate on plans the manual control type & locations served; C405.2.12 controls Indicate of plans the 50/o lighting load reduction method provided or identify exception taken Indicate lighting system automatic shut-off capability - identify lighting zone areas served on plans; Automatic time switch C405.22.1 controis and override Indicate locations of override switches on plans and the areas switching served, i�clude area sq. ft.; Indicate locations where automatic shutoff is provided by other methods (occuoancv sensor. davliaht controls. etcl C40522.2 Occupancy sensors Indicate on plans the locations served by occupancy sensors Daylight zones - Indicate vertical fenestration primary and secondary daylight zone C40522.3 Vertical fenestration areas on plans, include sq. ft.; and skylights Indicate sk i ht da i ht zone areas on plans, include s. ft. Indicate on plans the locations served by daylight zone controls; C405.22.32 Daylight zone controls Indicate in plans the lighting load reduction (dimming) method - stepped or continuous dimminq Specific application C405.2.3 lighting controls - C405.2.3 - Display and accent Items 182 lighting C405.2.3 - Hotel/motel guest Item 3 rooms Indicate on plans the locations served by specifc application lighting controls Indicate lighting control method for display and accent lighting, and display case lighting; Indicate these fixtures are controlled independently from both general area lighting and other lighting applications within the same Provide a lighting control device at each guest room entry for all permanently installed fixtures in guest room; Indicated whether liahtina control is manual or automatic C4052.3 - Supplemental task Provide automatic shut-off vacancy controls for supplemental task Item 4 lighting lighting, including under-shelf or under-cabinet lighting Identify eligible non-visual applications and method of lighting control; C4052.3 - Lighting for non-visual Item 5 applications Indicate these fxtures are controlled independently from both general area lighting and other lighting applications within the sam Indicate lighting control method for lighting equipment for sale or C405.2.3 - Lighting equipment for demonstration; Item 6 sale or demonstration Indicate these fiMures are controlled independently from both general area lighting and other lighting applications within the sa C4052.3 - Means of egress Item 7 lighting C405.10 Cooler and freezer C405.11 lighting C405.2.4 Exterior lighting controls Exterior building C405.6.1 grounds lighting control s C408.3 Lighting system functional testing If egress lighting power density is greater than 0.05W/ft�, indicate method of automatic shut-off during unoccupied periods; Identify on plans the egress fixtures that function as both normal and emergency means of egress illumination Provide vacancy device or timer to turn off fixtures within 15 minutes of unoccupancyfor cooler and freezer lighting fxtures with lamp efficacy less than 40 lumens per watt Indicate on exterior lighting plans the automatic lighting control method and locations served Provide motion sensor controls for building grounds fixtures rated at greater than 100 watts with lamp efficacy less than 60 lumens, or identify exception taken Identify applicable commissioning documentation requirements per Section C408 or eligibility for exception; Provide written procedures for functional testing of all automatic controls and describe the expected system response; IIdentify in construction documents the party responsible for functional testing of automatic lighting controls INTERIOR LIGHTING POWER & EFFICACY Sections C405.5, C405.10, C405.11 Provide fixture schedule with fxture types, lamps, ballasts, and rated watts per fixture; C405.5.1 Identify spaces eligible for lighting power exemption on plans and in C405.5.1.1 Total connected compliance forms; C405.5.1.2 interior li htin ower C405.5.1.3 9 g P Identify lighting equipment eligible for exemption in fixture schedule r.ans s � d and in compliance forms;